very smallSMOoth pulleyQ2/ Determine the load (W) for the bar(ABCD) shown in Fig.I which issupported(250mm')cable with very siall siothpulley and vertical (300mm?) cable at (C)and a horizontal roller at (D), The stress inall cables is limited to 150MPA.at(A)and(B)by45°3.0rm1.Om 1 On

Answered: Image /qna-images/answer/9a70d77c-3fd1-4f91-8829-39d68d56654f.jpg

very small smooth pulley Q2/ Determine the load (W) for the bar (ABCD) shown in Fig.I which is supported (250mm)cable with very sinall sunoth pulley and vertical (300mm2) cable at (C) and a horizontal roller at (D), The stress in all cables is limited to 150MPA. E at (A) and (B) by 43 A 3.0m 1.Om L On

very small smooth pulley Q2/ Determine the load (W) for the bar (ABCD) shown in Fig.I which is supported (250mm)cable with very sinall sunoth pulley and vertical (300mm2) cable at (C) and a horizontal roller at (D), The stress in all cables is limited to 150MPA. E at (A) and (B) by 43 A 3.0m 1.Om L On

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Design of machine elements solve according to Khurmi Please write clearly
4. A steel rod of length L and uniform cross sectional area A is secured between two walls, as shown. Use L=1.7 m, E = 200 GPa, a = 11.9 × 10-6 /°C and AT = 70 °C. Calculate the stress for a temperature increase of AT for: a) The walls are fixed. b) The walls move apart a distance 0.4 mm. (20 pts)
Solve the problem stated below. Use bond papers and black ball pen. Make your solution clear and clean. Draw the FBD. PROBLEM Figure: A homogeneous bar AC with negligible mass is supported by a pin at A and cable cable BC, which carries a load of 20 kN as shown in the figure. a) Determine the force reaction at A, (PA). b) If the shearing stress is 80 MPa (double shear), determine the pin diameter at A. 5 m. 3 m pin 4 m double shear 60° 20 kN
HW: 1-1-12 Find the axial stress in rods AB and BC. AB has a diameter of 25 mm and BC has a diameter of 15 mm. State if they are in tension (T) or compression (C). Answer(s): B A 6000N 8000N
A mechanism carries a constant load P applied to the seat as shown. For the angle 8, determine the following (a) the lengths LBE and LAB, in m (b) the angles a and p, in degrees Draw the complete FBD of (c)members AB, FG, EBH and GHI Calculate the forces, in Newtons, for the following (d) member FG (e) pin H (f) hydraulic cylinder AB Parameter P = 724 N 8= 34.5° Note: Figures CDFE and EFGH are parallelograms. E 100 175 bis is not y 400 LBE ou op os dadog on funt an 150, B a This is not property so do not in any way are your an 150 D E 175 B 200-- Dimensions in millimeters G PH P 150 This is not your property so do not use it in any way as if it were your
A closely coiled helical spring is made of 6 mm diameter steel wire, the mean diameter of the coil is 60 mm and there are 8 coils. Taking the modulus of rigidity as 100 kN/mm2, find the stress, in kPa, in the wire when carrying an axial load of 529N.
mm. NegiCOL UIC wOg VA vUampvuva 1.4-12 A rigid member DAC as shown in Fig. P1.4-12 carries the load P. Bar AB is an aluminum bar whose cross-sectional area is 0.5 in, and it is pinned at A and B by 0.5-in-diameter pins in a single-shear configuration. If the maximum allowable normal stress in AB is 7000 psi and the maximum allowable shear stress in the pins is 15,000 psi, find the maximum allowable load P. For aluminum E 10 x 10° psi. %3D 8 ft 7 ft P B Fig P1.4-12
I need the answer quickly
7
The mechanical assembly shown in the figureconsists of an aluminum tube, a rigid end plate, andtwo steel cables. The slack is removed from the cablesby rotating the turnbuckles until the assembly is snugbut with no initial stresses. Afterward, the turnbucklesare tightened by 1.5 turns. Calculate the forces inthe tube and the cables and determine the shorteningof the tube. As = 0.85in2 for each cable, AA = 4.5 in2,L = 20 in., Es = 29,000 ksi, EA = 10,600 ksi, andp = 1/16 in.
Fig. (6)
a 4ll Asiacell Q2 A 20 mm diameter steel rod passes concentrically through a bronze tube (200+SN) mm long, 50 mm external diameter and 40 mm internal diameter. The ends of the steel rod are threaded and provided with nuts and washers which are adjusted initially so that there is no end play at 25°C. 1. Assuming that there is no change in the thickness of the washers, if the stress produced in the steel is (200+SN) MN/m2 when one of the nuts is tightened, the pitch of the thread being 1 mm. Find the number of turns for the nut and stress in bronze tube.2. If the temperature of the steel and bronze is then raised to 40°C find the changes that will occur in the stresses in both materials. The coefficient of linear expansion per C is 10 x10-6 for steel and 17 x10-6 for bronze. E for steel = 210 GN/m2. E for bronze = 100 GN/m2. Where SN=3 إجابتك