Difficulty (3/5) Dimensions: a b 44 in 0.033 in by sare and-p 8900 Problem Statement: A cylindrical pressure vessel with dimensions given carries an internal pressure of 21 psi Find the axial stress and the hoop stress induced in the wall of the vessel Answers: be sure to include units with your answers

Q: A cable steel has a length of 100 m and stretch to 5 cm when the load is applied at both ends. If…

A: Using the basic formula of strength of materials

Q: HOMEWORK: A 24-inch long. round A36 steel rod resists a tensile load of 10,000# a.) What is the…

A:

Q: Q=6 A rocket is launched from Cape Canaveral. As it reached a height of 120 km. How much eastward…

A: Q6:   Given: The height of the rocket, h = 120 km

Q: Нome work 1. A shaft 80 mm diameter transmits power at maximum shear stress of (63 MPa). Find the…

A: As given question  Shaft diameter =80mm Key wide=20 mm Stress on key =42 mpa We have to determine…

Q: Compare the weights of equal lengths of hollow shaft and solid shaft to transmit a given torque for…

A:

Q: You are required to size member FI of the truss shown at right using Western lumber with the…

A: given loads act at point A, B, C and D is 2000lb in magnitude   Yield stress in compression: 2100…

Q: Q2- the magnitude of the minimum normal stress in the beam and where within the beam it is achieved.…

A:

Q: Given is a thin-walled tube with the following data: Wall thickness- 2mm ABC is a sector with a…

A:

Q: pls find box ur answer Determine the value of the von Mises stress at point A. The von Mises stress…

A: The values are P=4 kN, F=0.55 kN, T=25 Nm The yield stress is Sy=280 MPa The length of the pipe is…

Q: A part of the structure for a facory automation system is a beam that spans 30.0 inches as shown…

A:

Q: 2. A 6 x 19 IPS wire rope has a wire rope diameter of 50.8 mm and sheave diameter of 40 in. Find the…

A:

Q: Q2: Consider the steel spring in the illustration. (a) Find the pitch, solid height, and number of…

A: Dear student, we are suppose to solve only 3 sub parts. Please post other question as a separate…

Q: A hollow steel shaft, 500 mm outside diameter and 300 mm inside diameter, has a coupling 80 mm thick…

A: Given data: Outside diameter of hollow shaft = 500 mm                    Inside diameter of hollow…

Q: A1.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: the hot air balloon tethered to the ground by three cables, based on the information in the image…

Q: A water tank, 6 m in diameter, is made from steel plates that are 13mm thick. Find the maximum…

A:

Q: Please write it out. I don’t like the computer typed answers. Need help on all questions. Please…

A:

Q: 1. A cold-drawn AISI 1015 steel tube is 300 mm OD by 200 mm ID and is to be subjected to an external…

A: Given data - Outer diameter - 300 mm Internal diameter - 200 mm Yield strength = 600 Mpa It is asked…

Q: I need to find the forces in each tube but I keep getting stuck. I have been getting really long…

A: Given:To find:Force in each tube.

Q: The rotating shaft shown is subjected to a constant force. Shaft material is AISI 1020 cold drawn…

A:

Q: A screw jack was used to replace the tire of a dumper. The jack had to support a load of 2000 kgf.…

A: Load W = 2000 kg-fThe parameters of the screw jack -Mean diameter d = 30 mmLength of lever L = 500…

Q: If the figure below, the radius is ksi

A:

Q: Compute the resultant force acting on the pin at C (in kN).

A:

Q: Two aluminum circular shafts (E=70GPA) are mounted according to the figure. The two shafts have the…

A: r1 = 6.9 mm r2 = 11.11 mm L1 = 1.52 m L2 = 1.29 m P = 2.1 kN

Q: Please solve this question with all details please (handwritten) I will give like if it’s correct

A: