7. A wooden storage vat is 6 m in diameter and is filled with 7 m of oil, s = 0.8. the wood staves are bound by flat steel bands, 50 mm wide by 6 mm thick, whose allowable tensile stress is 110 MPa. What is the required spacing of the bands near bottom of the vat, neglecting any initial stress?

7. A wooden storage vat is 6 m in diameter and is filled with 7 m of oil, s = 0.8. the wood staves are bound by flat steel bands, 50 mm wide by 6 mm thick, whose allowable tensile stress is 110 MPa. What is the required spacing of the bands near bottom of the vat, neglecting any initial stress?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.5.2P: A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is...

See similar textbooks

Related questions

Q: Find the volume of the propane tank. Assume IPS units, set before you begin to sketch the part.. The…

A: Given Data A = 9.75 Material: AISI Steel 1020 Find Find the volume of the propane tank.

Q: Can you write me a program manuscript using geometric definition on FAPT language. The starting…

A: To create a part program for the given part drawing (Fig. 2) for a wire electric discharge machine…

Q: The answer is one of the options below please solve carefully and circle the correct option Please…

Q: Lathe Machine Operations Create a list of operations for the blueprint provided below. The answers…

A: for this part the list of operation to be followed to make the above blue print is as follows…

Q: What is the location of FR, i.e., the distance d? (a) 2 m, (b) 3 m, (c) 4 m, (d) 5 m, (e) 6 m. 3 m 3…

A: To determine:The location of FR ie the distance d.

Q: question from ENGINEERING DRAWING BY N.D BHATT Write all steps of drawing following 3D model in…

A: Given: geometry as shown

Concept explainers

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.

Question

SHOW COMPLETE AND DETAILED SOLUTION.

PLEASE WRITE LEGIBLY.

GIVEN:

SOLUTION:

7. A wooden storage vat is 6 m in diameter and is filled with 7 m of oil, s = 0.8. the
wood staves are bound by flat steel bands, 50 mm wide by 6 mm thick, whose
allowable tensile stress is 110 MPa. What is the required spacing of the bands near
bottom of the vat, neglecting any initial stress?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
A hemispherical window (or viewport) in a decompression chamber (see figure) is subjected to an internal air pressure of 85 psi. The window is attached to the wall of the chamber by 14 bolts. (a) Find the tensile force Fin each bolt and the tensile stress (T in the viewport if the radius of the hemisphere is 14 in. and its thickness is 1.25 in. (b) If the yield stress for each of the 14 bolts is 50 ksi and the factor of safety is 3.0, Find the required bolt diameter. (c) If the stress in the viewport is limited to 500 psi, find the required radius of the hemisphere.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
: A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered into a lake (see figure). The compressed air in the tank is at a pressure of 24 psi (gage pressure when the tank: is out of the water). At what depth D0will the wall of the tank be subjected to a compressive stress of 90 psi?
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
Q6 A spherical vessel of 1.6m inner diameter is constructed by joining two hemispheres with equally spaced bolts as shown in fig.3. The vessel will operate at an internal pressure of 600kPa. Calculate the vessel plate thickness t. Given the allowable stress for the sphere plate will equal 50MPa. If the same plate was used to make a cylindrical vessel to operate at the same internal pressure, find the cylinder maximum allowable diameter. ... المزيد A Ľ تعديل حذف 0 المفضلة Lo مشاركة
Example: A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is 1 m long. It is found to change in internal volume by 12.0 x m' when filled with a liquid at a pressure p. If E = 200GN/m2 and y= p.25, and assuming rigid end plates, determine: (a) the values of hoop and longitudinal stresses; (c) the necessary change in pressure p to produce a further increase in internal volume of (longitudinal) are assumed; 15 %. The liquid may be assumed incompressible.
A wood stave pipe, 120 cm in inside diameter, is to resist a maximum water pressure of 1,200 kPa. If the staves are bound by steel flat bands (10 cm by 2.50 cm), find the spacing of the bands if its allowable stress is 105 MPa.\ Please explain the steps and formulas used.
A scuba tank is being designed for an internal pressure of 2,685 psi with a factor of safety of 2.0 with respect to yielding. The yield stress of the steel is 66,000 psi in tension and 30,000 psi in shear. (Assume that the given radius or diameter is an inside dimension and that all internal pressures are gage pressures.) (a) If the diameter of the tank is 7.0 in., what is the minimum required wall thickness (in inches)? inches (b) If the wall thickness is 0.25 in., what is the maximum acceptable internal pressure (in psi)? psi
Calculate the combined stress (MPa) on the rod shown below using principle stress method.Here, F1 = 0.35 kN, F2 = 0.12 kN, T = 428000 N-mm. Length and diameter of the rod are 75cm and 75 mm, respectively.