Example: A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is 1 m long. It is found to change in internal volume by 12.0 x m' when filled with a liquid at a pressure p. If E = 200GN/m2 and y= p.25, and assuming rigid end plates, determine: (a) the values of hoop and longitudinal stresses; (c) the necessary change in pressure p to produce a further increase in internal volume of (longitudinal) are assumed; 15 %. The liquid may be assumed incompressible.

Example: A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is 1 m long. It is found to change in internal volume by 12.0 x m' when filled with a liquid at a pressure p. If E = 200GN/m2 and y= p.25, and assuming rigid end plates, determine: (a) the values of hoop and longitudinal stresses; (c) the necessary change in pressure p to produce a further increase in internal volume of (longitudinal) are assumed; 15 %. The liquid may be assumed incompressible.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A 200 x 100 x 50 mm steel block is subjected to a hydrostatic pressure of 15 MPa. The Young's…

Q: Plot the variation of Ex, Gxy, νxy, mx, and my for a lamina with the following properties: EL = 35…

A: Given:To find:Plot the variation of Ex, Gxy, νxy, mx, and my for a lamina.

Q: can you resolve the problem but with 10mm diameter, l=100mm, P=7850N, change in diameter =…

Q: A closed cylinder (26 + 60) cm long, containing 3 MPa pressurized fluid, due to this pressure a…

A: Since we provide answers up to three subparts only, we will answer the first three subparts here.…

Q: cylindrical vessel of 1 m diameter and 3 m long is made of steel 12 mm thick and filled with water…

Q: A cylindrical tank containing thickness Q2) compressed air has wall t 12mm and inside radius r=…

A: The stress that tends to burst a cylindrical pressure vessel circumferentially is termed…

Q: A thinwalled, filamentwound pressure vessel is pressurized such that at a point in the wall is in…

A: Since we are allowed to 3 subparts at a time. we’ll answer the first 3. Please resubmit the question…

Q: "he rigid bar of negligible weight is supported as shown. The assembly is initially stress-free.…

Q: A copper cylinder 150mm outside diameter has walls 25mm thick. End plates are stayed by a 25mm…

Q: The tank shown in Figure below is fabricated from t = 1/8 in steel plate. The naximum longitudinal…

Q: A closed cylinder (92) cm long, containing 3 MPa pressurized fluid, due to this pressure a change in…

Q: A steel pipe of length L= 5 ft, outside diameter d₂= 9.3 in., and inside diameter d₁= 4.7 in. is…

Q: of mean radius R, thickness t and length L, has its ends closed and is full of water. If the ends…

Q: Figure Q5 shows a thick cylinder of [A] mm intemal radius and [B] mm outer radius is subjected to an…

A: (a)

Q: Find the width of a heavy-single ply leather belt (8.75 hp/in) transmitting 11 hp at 1800 rpm motor…

A: Given, Heavy - Single ply leather belt Power, p = 11hp; Speed of the motor, N = 1800 RPM cm =0.696…

Q: The roof over a 9.0-m x 10.0-m room in a school has a total mass of 12900 kg. The roof is to be…

Q: Water at pressure p; flows through an underground cast iron pipe. The outer surface of the pipe is…

A: It is asked to find the suitable finite element idealization for a pipe of length 1000 m. The pipe…

Q: A steel pipe of length L= 5 ft, outside diameter d₂= 9.3 in., and inside diameter d₁= 5.1 in. is…

A: Given:Length of the pipe, L=5 ftOutside diameter, d2=9.3 inInside diameter, d1=5.1 inAxial force,…

Q: In a biaxial state of stress, normal stress are 900 N/mm^2 and 100 N/mm^3 in x and y diretion…

A: Given data σx=900 MPaσy=100 MPaτxy=300 MPa

Q: A thin cylinder 95 mm internal diameter, 500 mm long with walls 4.5 mm thick is subjected to an…

A: A thin cylinder is a cylinder in which the thickness is the 20th part of the diameter or even less.…

Q: 03. A welded steel cylindrical drum made of a 15mm thickness plate has an internal diameter of 1.50…

Q: aking E=200GPa, A 200 × 100 × 50 mm steel block is subjected to a hydrostatic pressure of 15 MPa.…

A: Given:Dimension of steel block=200×100×50 mmHydrostatic pressure=15 MPaE=200 GPaϑ=0.3Find,Change in…

Q: The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a…

A: (a) To find: The axial force F in the ring in terms of p, w and r; Calculation: Consider a FBD by…

Q: Q.2 A thin cylindrical shell, 1.5 m internal diameter, 2.4 m long, internal volume 4-23 m³, plates…

Q: The rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute the…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Example: A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is 1
m long. It is found to change in internal volume by 12.0 x m' when filled with a liquid at a
pressure p. If E = 200GN/m2 and y= p.25, and assuming rigid end plates, determine:
(a) the values of hoop and longitudinal stresses;
(c) the necessary change in pressure p to produce a further increase in internal volume
of (longitudinal) are assumed; 15 %. The liquid may be assumed incompressible.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 - Given Data

VIEW

Step 2 - Calculation

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A spherical tank of diameter 1.275 m and wall thickness 40 mm, contains compressed air at a pressure of 17 MPa. What is the absolute maximum shear stress?
Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at apressure of 5.75 MN/m2 . The diameter of the vessel is 400 mm, and the stress is limited to28.75 MPa.
A steel pipe of length L= 3 ft, outside diameter d₂- 10 in., and inside diameter dy = 5.1 in. is compressed by an axial force P= 107 kips. The material has = Poisson's ratio v=0.30. Determine the increase in thickness.
A steel (E=210 GPa, v=0.32) cylindrical vessel has a diameter R= 25 cm, thickness t=0.2 cm and length L=100 cm. What is the increase in the length of this vessel if it is subject to PR PR. an internal pressure P kPa (unit in kPa)? (Remember: o, =
A gas is stored in a cylindrical tank of inner radius 7 m and wall thickness 50 mm. The gage pressure of the gas is 2 MPa. The maximum shear stress (in MPa) in the wall is
The axially aligned pressure vessel, shown in Fig Q2, is made from aluminium exhibiting a Young's Modulus of 73GPa and a Poisson ratio of 0.34. It has an outer diameter D, of 86mm and a wall thickness t of 5mm. The vessel is subject to an internal pressure P of 150bar and externally applied torque T of 4.5kNm. a) Draw the 2D planar state of stress of any finite element located on the outer surface of the pressure vessel, according to the polar coordinate system provided. b) Sketch the longitudinal, circumferential and planar shear strain profile through the thickness of the vessel wall. c) Determine the minimum factor of safety for the given load cases, assuming the aluminium has a yield strength of 175MPA, and comment on the most likely mode and locus of failure. theta i. - Z - T Do Section A-A: Side View End View
Problem 3 A large spherical tank (see figure) contains gas at a pressure of 3.5 MPa. The tank is 20 m in diameter and is constructed of high-strength steel having a yield stress in tension of 550 MPa. (a) Determine the required thickness of the wall of the tank if a factor of safety of 3.5 with respect to yielding is required. (b) If the tank wall thickness is 100 mm, what is the maximum permissible internal pressure? (Assume that the given radius or diameter is an inside dimension and that all internal pressures are gage pressures.)
Please find me solution of this problem a and b
As figure show are depicts the cross-section of a closed-end cylinder with an internal diameter of 0.2 m and an exterior diameter of 0.4 m with a thick-walled pressure vessel (closed-end cylinder) with an internal diameter of 0.2 m and an external diameter of 0.4 m. Both internal and external pressures, Pi and P, are applied to the pressure vessel. Find the following given P. = 10 MPa:a). The internal pressure Pi, which will result in a 150 MPa tensile hoop stress at point B, which is in the middle of the cylinder wall.b). Draw all of the stress distributions over the wall thickness and their stress values on the cylinder's inner and outer surfaces.c). The longitudinal tension that the cylinder is subjected to.
Q4/ cylinder has an internal diameter of 200 mm, has walls 3 mm thick and is 1.2 m long. It is found to change in internal volume by 11x10 m' when filled with a liquid at a pressure p. If E=200 GN/m? of hoop and v-0.25 determine the values and longitudinal stresses?
A thick-walled tiub with internal diameter, D; = 160 mm and external diameter, Do = 320 mm is acted by the external pressure, po. The tube is made of steel with Young's modulus of 200 GPa and yield strength of 210 MPa. Considering the open-end condition; (a) determine the maximum pressure, po that could be carried by the tube for yielding the wall material based on the Maximum-Shear-Stress theory (Tresca). (b) Using the result of part (a), calculate the stresses in the tube wall material at both internal and external radius positions. Sketch the corresponding stress element. (c) Draw the yield locus in the principal stress space (o versus o2) and indicate the yield stress value. Show, on the diagram, the state of the stress as calculated in part (b).