A cylindrical tank containing thickness Q2) compressed air has wall t 12mm and inside radius r= 250mm. The stresses in the wall of the tank acting on an inclined element have the values shown in the figure. What is the air pressure P in the tank? Determine 0. 82MPa, 124MMPa %3D 28MMPa

Q: what is 6 to 10 po?

A:

Q: answer the next part pls

A: From the previous solution: Pitch circle diameter→D=4 inch Number of teeth→T=16 Hence the circular…

Q: Find 150Am 120mm V- 100 mm

A: Consider the below diagram,

Q: salve gine a- when

A: givendifferential equation xdydx+cosy=0y=π4  when x=2

Q: how does F_BC equal 6

A:

Q: y' = -y tan x, y(0) = 2

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 1. What is the type of robot?

A: ***As per our company policy we are supposed to do only 1 question if you need the rest please…

Q: ove that the calculated values ne graphical method and the ematical analysis method the same, for…

A:

Q: A disk of mass, m, and radius, R as shown in the figure is being supported by an elastic shaft with…

A:

Q: LA 5 mm 28 mm ー-ギー - 49 mm 49 mm

A: For triangle, X1= 0 Y1= (1/3)×95= 31.67 mm  A1 = 1/2 × 98× 95 = 4655 mm2 For semi circle, X2 =0 Y2=…

Q: 2.36x178×106 1- 1 0.9x300x368²×30 Prequired 400 (1.18 30)

A: Given Data⇒

Q: ldentify the valvetrain components in the drawings. Place the identifying letter next to the name of…

A: Valve train get together for a gas powered motor contains a typical transporter which upholds the…

Q: D 3.2-5. Use the graphical method to demonstrate that the fol- lowing model has no feasible…

A:

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: Q1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket…

A:

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: Tät-/e205+(17-78 2.

A: Given Data⇒a↦=202+17.782

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: how can I get the 85 α

A:

Q: What is the worst-case distance between the bottom surface of the slot and the botto surface of the…

A: Given drawing

Q: Create an example of Hooke's Law

A: To create: The example of Hooke's law. Concept used: Hooke's law: Hooke's law states that the…

Q: A piezometer and a pitot tube (close to each other, as described in the figure) are connected to the…

A:

Q: Find the maximum height of the water that would still allow you to open the door, using the same…

A: Answering the fourth question as the third question is being answered earlier It is asked to find…

Q: continue the question

A: Given: (d) The dimension of the plate: →A=1.2m*1.2m Because the distance of the center of gravity of…

Q: In this case, the applied force is always pulls upward, but the amount of force that can be applied…

A: According to the given data  We need to find The true statement

Q: If a = 9 in., locate the distance to the centroid of the member's cross-sectional area. (Figure 1)…

A: Draw the given diagram.

Q: Findss 30 kN-m

A:

Q: Which of the following statements is FALSE regarding materials experiencing stress within the…

A: Given Stress vs strain plot To write:  WHich statement is false

Q: A differential element on the bracket as shown in Figure Q1 is subjected to plane strain that has…

A:

Q: M, B

A: Given data, The reaction at A and B can be calculated as -

Q: Figure 1 of 1 30 40 F2

A: Given, F1 = 210 N F2 = 510 N Angle between two forces = θ = 40°

Q: What is the location of FR, i.e., the distance d? A M 3 m 3 m F. R B

A:

Q: Through the two pipes in Figure 6 flow equal flows of water. data: Pipe diameter No. 1: 200 mm -…

A:

Q: The point 1/4 of the way from (1,-3, 1) to (7,9, –9) is A. (4,3,-4) O B. (3/2,3,-3/2) OC.…

A: A point's coordinates are a pair of integers that define its precise position on a two-dimensional…

Q: How do you know that it is -1.2? What determines the sign?

A: Given: How do you know that it is -1.2? What determines the sign?

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.