Rigid (plate Aluminum tube Steel cable Turnbuckle -L-

Q: a b c d h   82 mm     139 mm     39 mm     18 mm     33 mm   Clamps like the one shown are commonly…

A:

Q: Question 3-5: Truss is loaded as shown: 24 KSI in tension 18 KSI in compression Question 3 A 8 ft…

A:

Q: Two plates of which (2.5 d) and d as outer and inner diameter respectively and thickness 25 mm each…

A:

Q: The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the…

A:

Q: 3.40-3.41 For the space trusses shown in Figures P3-40 and P3-41, determine the nodal dis-…

A:

Q: In the figure below, a pulley can pull a 1-ton load from rest to 3 m/s upwards at 2 seconds. AB and…

A: Given: The load, W = 1 ton The speed, v = 3 m/s The time, t = 2 s The compressive stress, σ = 140…

Q: The frame shown is fitted with three 28 cm diameter frictionless pulleys. A force of F' = 640 N is…

A:

Q: below shows a stee! bar 07 mass m The 7igure which is placed against a wall. There is no betneen the…

A:

Q: 3 cables with same diameter are used to hold the plate. Calculate the tensile loads in all cables if…

A: Givencables with load as  shown below

Q: A 7.5kg sign is hung off of the end of a 3.7kg metal arm as shown in the figure. (Note that while…

A: Given Data: The mass of the arm is m1=3.7 kg. The mass of the sign is m2 = 7.5 kg. The center of…

Q: Q2. As shown in figure, the allowable stress for tension is 200 MPa and the allowable stress for…

A:

Q: Find the force in member HI

A:

Q: The truss below is subject to the loads as shown. All of the members are attached at plates and can…

A:

Q: Clamps like the one shown are commonly used in woodworking applications. This clamp has the…

A: Solution: Given Data: t=49 mmP=115 kPaw=115000 Pa×0.049 m=5635 N/mμs=0.4

Q: A uniform bar AB weighing 424 kN, is fastened by a frictionless pin to a block weighing 200 kN as…

A: bar weight m1 = 424 kNblock weight m2 = 200 kNfriction factor between wall & bar f1 =…

Q: The 1.5 kN vertical OA pole is supported as shown in the figure and loaded with a horizontal force…

A: Given: The weight of the pole is 1.5 kN. The pole with the supported load is shown below:

Q: Q4/ The normal stress applied due to * :the axial force 10 KN is 10 kN he100 mm 2m Q5/ The axial…

A: Find normal stress due to axial load 10 kN.

Q: The frame shown is fitted with three 36 cm diameter frictionless pulleys. A force of F = 920 N is…

A:

Q: Find the tension in the cables and the reaction force point O

A:

Q: 1200 N 0.8 m D. 0.6 m 0.6 m 0.6 m FIGURE E4-8(1) The magnitude of the force transmitted thru Pin-E…

A: Diameter at pin E, DE= 16 mm= 0.016 m Diameter at pin D, DD= 12 mm= 0.012 m

Q: The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are…

A: given; ⇒stress(τ)=70MPa⇒diamater(d)=20mm⇒lets take number of rivit in BC =n1 ⇒lets take reaction…

Q: The truss below is subject to the loads as shown. All of the members are attached at plates and can…

A: Given:H=335 lbJ=211 lbFind:The internal resultant normal force in member CD

Q: Four wooden dowels with a diameter of 30mm are attached to a board. Two ropes pass around the…

A: Given data  Diameter = 30mm Force P= 110N and Q= 189N Find the resulting torque

Q: -1m 1m Ql: A: Draw a Free-Body Diagram of the bars AD and BC shown in the figure. Assume all hinges…

A:

Q: For the cantilever truss in Figure, determine the force in each member. | 100 N 60 30 5m 10 m 1000 N…

A: For  the given truss  To determine  forces in each member

Q: Problem 4-17: The pipe is stuck in the ground so that when it is pulled upward the frictional force…

A: To findDetermine the initial force P required to pull the pipe out and the elongation just before it…

Q: (a) Using the Force Method of Analysis, draw the shear force and bending moment diagram for Figure…

A:

Q: P-1500 kg 45 Py-4000kg k P:

A:

Q: In the figure, one end of a uniform beam of weight 130 N is hinged to a wall; the other end is…

A:

Q: A picture frame is hung using the ropes 3 mm in diameter as shown in the figure. The maximum stress…

A: For solution refer below images.

Q: A steel panel is subjected to a compressive loading in order to improve the panel stiffness and to…

A: Given:- F=400kips V= 0.20 E=2.8x107psi

Q: Consider the frame shown in (Figure 1). Suppose that F₁ = 26 kN. Part A Determine the x and y…

A:

Q: given plate below with width of 200 mm and thickness of 16 mm is to be connected to two plates of…

A:

Q: en truss, find the force of m = 60 kN olve this using two methods: (a) Metho

A: Given-Information:- Load 1 = 30 kNLoad 2= 60 kN To-Determine:- Force of member BH As given above…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.