Situation 4 - A load of W = 30 Li L2 kN is lifted through a boom BCD as shown in the Figure AP-4.10. The boom makes an angle of 60° with the vertical. Neglect the weight of the boom and for this w problem, L1 = L2 = 2 m. The pulley at D is frictionless. 10. Determine the angle a. Answer: 30° 11. What is the tension in cable 60° Figure AP-4.10 B AC in kN? Answer: 25.36 kN 12. What is the total reaction at B in kN? Answer: 54.77 kN

Situation 4 - A load of W = 30 Li L2 kN is lifted through a boom BCD as shown in the Figure AP-4.10. The boom makes an angle of 60° with the vertical. Neglect the weight of the boom and for this w problem, L1 = L2 = 2 m. The pulley at D is frictionless. 10. Determine the angle a. Answer: 30° 11. What is the tension in cable 60° Figure AP-4.10 B AC in kN? Answer: 25.36 kN 12. What is the total reaction at B in kN? Answer: 54.77 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the Tensions TCA and TCB for the system as shown in figure. Take R = 200 mm, S= 240 mm 0 = 55°, W= 14 kN ( Solve the problem in a paper and upload the file in a separate link provided. Also enter only the values in the boxes below. ) Tension TCA in N is Tension TCB in N is
13 В 30° 30° C D L. P P2 In the figure, L = 14 ft, P1 = 900 lb, and P2 = 550 lb. Compute the member forces listed below. In each case, tension is positive and compression is negative.
Requlred Information A countershaft carrying two V-belt pulleys Is shown In the figure. Pulley A recelves power from a motor through a belt with the belt tensions shown. The power Is transmitted through the shaft and dellivered to the belt on pulley B. Assume the belt tenslon on the loose side at B Is 15 percent of the tension on the tight side. Glven B(dg) = 400 mm, TA = 575 N, and TỊA2) = 3835.25 N. 300 450 400 TIA T(A2Y `150 250 dia. B(da) 20 dia. B At the point of maximum bending moment, determine the bending stress and the torslonal shear stress. The bending stress at the point of maximum bending moment is [.09515 MPа. The torslonal shear stress at the point of maximum bending moment is 259.442 MPа.
For two existing torques, what third force at a given distance from the pivot will balance them? Imagine a meter stick set up as in the figure. It hangs from a central bracket, and two hanging masses can hang from it from each of their brackets. At a third location, a force probe can either pull up or pull down on the stick, depending on what is needed to balance the stick. The mass of the meter stick is 120 g. sketch the situation (drawing r1, r2, r3, F1, F2, and F3) and determine the magnitude (value) and direction (+ or -) of each torque. Don't include the mass of a bracket that would hold the hanging mass in place; assume the mass listed is the entire mass hanging at that point. For each trial, use the principle of equilibrium (where the sum of torques is zero) to calculate the third, unknown force acting at x3
For two existing torques, what third force at a given distance from the pivot will balance them? Imagine a meter stick set up as in the figure. It hangs from a central bracket, and two hanging masses can hang from it from each of their brackets. At a third location, a force probe can either pull up or pull down on the stick, depending on what is needed to balance the stick. The mass of the meter stick is 120 g. sketch the situation (drawing r1, r2, r3, F1, F2, and F3) and determine the magnitude (value) and direction (+ or -) of each torque. Don't include the mass of a bracket that would hold the hanging mass in place; assume the mass listed is the entire mass hanging at that point. For each trial, use the principle of equilibrium (where the sum of torques is zero) to calculate the third, unknown force acting at x3
BAPS JUM uestion 1 Using the method of joints, find forces in each member of the truss shown in the figure below. 3 m D 60° 30° 3 m 60 30 A 500 kN
Force between A and B: 200lb Angle on D: 35 deg Angle on C: 50 deg
The system shown is composed of an ABG bar, supported by a pin at point A and by a collar smooth at point B (the collar slides on the bar ABG). The collar is pinned to the BDE bar, and the Rod BDE is supported by a pin at D and a cable at end E. Calculate the load P, such that the cable force EF is 20lb.
5
Please ans as. Soon possible
RAY F Enter Fpc: Enter Fr The figure above is a pin-joint frame with horizontal member length 1 = 2m and vertical member length h = 4m. (Note that the diagram is not to scale.) You are given that F₁ =45kN, RAY = 15kN and Rpy = 30kN. Use the method of sections to calculate the forces in members BC, FC and FE. Enter your answers in kilonewtons (kN) correct to 2 decimal places. Enter Fac: KN KN F₁ KN RDY
PROBLEM 1 Find the support reactions and joint force of the construction, shown on the figure, if: P-12 kN, q, q=9 kN/m and L=2 m, M = 9 Nm² A 2L K L B 12