В 25 C D 50 kg

Q: A beam supports has been shown in the bellow figure. The material is gray cast iron. The value of…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: The cross-sectional dimensions of a beam are shown. Assume b-2.5 in., t-tw-0.25 in. and d=4.25 in.…

A: a. Bending moment b. Bending stress

Q: The displacement of 0 and the rotation of beam KN

A: Hi! Thank you for the question As per the honor code, We’ll answer one question since the exact one…

Q: The spool of wire having a weight of 300 lb rests on the ground at B and against the wall at A.…

A: Given Data: Weight of the wire spool is W=300 lb. The coefficient of friction between the spool and…

Q: The cross-sectional dimensions of a beam are shown. Assume bf=2.5 in., tf=tw=0.125 in. and d=3.875…

A:

Q: A beam is used to support a concentrated load of 12 kN and a distributed load (w). The beam has the…

A: by the given figure RA+RC=-12+54=42KNtaking moment at hinge zeroRA×9-6×9×4.5RA=27KNorRC=15KNmaximum…

Q: A 10-kg cylinder D, which is attached to a small pulley B, is placed on the cord as shown. Determine…

A: The free body diagram of point B is given below. Consider the equilibrium of force in y-direction.

Q: In a flywheel, an 800N-m is applied as shown below with a coefficient of belt friction 0.20. Minimum…

A:

Q: For the given system below, rods A and B support the rigid bar, pinned at O, as it is subjected to…

A:

Q: 2-2: A wire of 2 mm diameter is wound round a circular shaft of 1 metre diameter. What are the…

A:

Q: The cross-sectional dimensions of a beam are shown. Assume by-2.125 in., t-tw-0.375 in. and d-3 in.…

A: Given data  Find  1. Moment about z-axis when bending stress generated at K is 2230 psi (tension).…

Q: QUESTION 2 Determine the value of P just sufficient to start the 60 wedge under the W lb blue block.…

A:

Q: 3. The beam ABCD is fixed with simple support of B and C as shown in the figure below. When point A…

A: Data given Find : Find loads P and Q to make point A and D equal to point B and C

Q: A rigid bar ABC is supported by three identical wires A, B, and C as shown in the figure. The bar…

A:

Q: The cross-sectional dimensions of a beam are shown. Assume b=2.5 in., t-tw-0.375 in. and d=3 in. (a)…

A:

Q: The cross section of a beam is a solid circle of radius 86 mm. The section is subject to a positive…

A:

Q: The static and The coefficient of kinetic friction is m =0.5 and m =0.4, respectively. h h The crane…

A: Given: The mass of the log is 500 kg. The coefficient of static friction is 0.5. The coefficient of…

Q: The cross-sectional dimensions of a beam are shown. Assume bf=3.375 in., tf=tw=0.3125 in. and d=3…

A:

Q: 2.0 Block A weighs 500.0 N and block B weighs 280.0 N. Block A is held by a cord fastened to the…

A:

Q: . In the figure below, the boom AC is supported in a ball and socket joint at C and by the cables AD…

A:

Q: A rope ABCD is looped over two pipes as shown. Knowing that the coefficient of static friction is…

A:

Q: The cross-sectional dimensions of a beam are shown. Assume b-1.875 in., t-tw-0.125 in. and d-2.75…

A: Bending stress at K 3340 psiDepth 2.75 inThickness of flange and web 0.125 inWidth 1.875 inTo find…

Q: The bell crank fits loosely into a 0.5-in-diameter pin. Determine the required force P which is just…

A: Consider the equilibrium of forces in x and y direction.

Q: A rope ABCD is looped over two pipes as shown. Knowing that the coefficient of static friction is…

A: Determine the smallest value of the mass m in kg for which equilibrium is possible. the…

Q: Consider a structure consisting of two bars of identical circular cross section as shown in figure.…

A:

Q: A rope ABCD is looped over two pipes as shown. Knowing that the coefficient of static friction is…

A:

Q: A beam having a tee-shaped cross section is subjected to equal (12 kN.m) bending moments, as shown…

A: Using bending equation. answer= 70.8 mpa (T)

Q: A rectangular beam is supported at both ends. It carries two concentrated load of 190KN, a clockwise…

A:

Q: The simply supported beam has the cross-sectional area shown. Determine the absolute maximu bending…

A: Given- Length of Beam =6 m