Below presents a continuous beam with A being fixed and B is pinned and C has a roller.Take: E = 200 GPa1 = 8 x 106mmLoad = 2 kNA5mBUsing the following method:2 KN+ 2m + 2m |-You are tasked to analyze the continuous beam by calculating the:> the displacement on the beam at B and C and> the reaction at the supportsMatrix Structural AnalysisUse the following steps as a guide to analyze the beam:Matrix Structural Analysis✓ Produce Notations✓ Establish the known displacements and known external load✓ Produce Member Stiffness Matrix✓ Displacement and Load✓ Calculating the displacementCalculating the reaction at the support

Answered: Image /qna-images/answer/df34dec3-e278-4a45-a469-104121936024.jpg

Answered: Below presents a continuous beam with A…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer completely and legibly about stress and strain
Consider a rectangular cross-section beam having width b and height h that is taking bending load. The beam can be oriented in two different ways (shown in case a and b), and the corresponding neutral axes are shown as well. In which case, the beam will provide more resistance to bending (i.e., larger value of 1)? b Case (a) Neutral axis O I. Case (b) O II. Depends on other parameters III. Case (a) IV. Both cases will give the same value of I Case (b) Neutral axis
6...
The 16 x 22 x 25-mm rubber blocks shown are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 238 N causes the upper frame to be deflected downward by 4 mm. Determine the shear modulus G of the rubber blocks. Double U anti-vibration shear mount 25 Rubber block dimensions Shear deformation of blocks O 0.745 MPa O 0.883 MPa O 1.140 MPa
Please help me solve this, Thank you so much.
A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The cross-sectional area of the rod is 50 mm². Neglect the size of the couplings at B, C and D. Calculate the displacement of the rod at D when F₁ = 2.8 kN, F₂ = 4.3 kN and F3 = 7.3 kN. Input your answer as a value only in mm to two decimal places without +/-sign. 1m 1.5 m 1.25 m C F2 D F3 A F₁ B
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h= 430 mm tw= 12 mm d= 110 mm t= 9.6 mm Additionallv: • The area of each pipe is A = 3028 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is I>= 320410000 mm4. If the beam will be subiected to a shear force of V = 110 kN, determine the shear stress at point K, located at yK = 70 mm below the z centroidal axis.
3. Rigid member ABD is connected to elastic member CDE as shown. For the given loading, what are the vertical displacements of points A and E? A 20kN dimensions in meters B rigid C T 0.4 D E 0.2 5KN E=7oGPa A=100mm²
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 12 mm d = 100 mm t = 6.4 mm Additionally: • The area of each pipe is A = 1882 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is lz=171660000 mm4. If the beam will be subjected to a shear force of V = 120 kN, determine the shear stress at point H, located at yμ = 100 mm above the z centroidal axis. H Hv K Answer: TH= X MPa Ун Ук K Iv
The piece of plastic is originally rectangular. Suppose that a = 300 mm and b = 450 mm. A) Determine the shear strain γxy at corner C if the plastic distorts as shown by the dashed lines.
For the beam shown, calculate the bending stress at a point 70 mm. from the top of the beam. P = 59, a = 233, b = 296 Round your answers to 2 decimal places.
There is a wooden beam AD, as shown in the figure below, the Flexural Rigidity of the beam section is constant EI:(a) Try to find the slope of point A and point C after deformation.(b) Try to find the (vertical) displacement of point D after deformation.(c) What is the position and magnitude of the maximum displacement after deformation?

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Below presents a continuous beam with A being fixed and B is pinned and C has a roller. Take: E = 200 GPa 1 = 8 x 10 mm* Load = 2 kN 5m 2 KN + 2m + 2 m ▸ the displacement on the beam at B and C and the reaction at the supports F You are tasked to analyze the continuous beam by calculating the: