5. A rigid bar AB, 9 m long is suspended by two vertical rods at its end A and B and hangs in ahorizontal position by its own weight. The rod at A is brass, length 3m, cross-sectional area is1000 mm? and E̟ =1×10°N/ mm? . The rod at B is steel, length 5 m , cross-sectional area is 445mm?. At what distance 'd' from A may a vertical load P=300ON be applied if the bar is to remainhorizontal even after the load is applied?ve stredSteel5mBrass3mP = 3000NB9m

Answered: Image /qna-images/answer/2a98758a-7287-4fa5-80f5-26863119b55d.jpg

5. A rigid bar AB, 9 m long is suspended by two vertical rods at its end A and B and hangs in a horizontal position by its own weight. The rod at A is brass, length 3m, cross-sectional area is 1000 mm? and E, =1×10°N /mm² . The rod at B is steel, length 5 m , cross-sectional area is 445 mm?. At what distance 'd' from A may a vertical load P=3000N be applied if the bar is to remain horizontal even after the load is applied? Steel 5m Brass 3m P = 3000N A 9m

5. A rigid bar AB, 9 m long is suspended by two vertical rods at its end A and B and hangs in a horizontal position by its own weight. The rod at A is brass, length 3m, cross-sectional area is 1000 mm? and E, =1×10°N /mm² . The rod at B is steel, length 5 m , cross-sectional area is 445 mm?. At what distance 'd' from A may a vertical load P=3000N be applied if the bar is to remain horizontal even after the load is applied? Steel 5m Brass 3m P = 3000N A 9m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the vertical movement of P if P is 120 KN.
The wood column is pinned at its base and top. Determine the maximum eccentric force P the column can support without causing it to either buckle or yield. Take E = 10 GPa and s Y = 15 MPa.
Determine the magnitude of the pin force at A. Assume W = 795 lb, a = 3.9 ft, b = 2.8 ft, r = 7 in. r W C Answer: A = i a B A D lb b
The initial compressive force of a steel column can be determined by Euler's buckling formula. The column has the following properties: A = 9484 mm² Fy=345 MPa x = 164 x 106 mm4 ly = 23 x 106 mm4 Proportional limit, fs = 290 MPa The x-axis has an unbraced length of 10 m which is pinned at the top and fixed at the bottom with an k = 0.70. The y-axis has unbraced length of 5 m due to the bracing at the mid-height. Compute the initial compressive load of the column. Select the correct response: 6606.59 KN 3706.14 KN E = 200 GPa 1816.01 kN 926.53 kN
o
A portal frame shown in figure (not drawn to scale) has a hinge support at joint P and a roller support at joint R. A point load of 50 kN is acting at joint R in the horizontal direction. The flexural rigidity. El, of each member is 106 kNm². Under the applied load, the horizontal displacement (in mm, round off to 1 decimal place) of joint R would be Q P FIAT 5 m EI pole El 10 m R 50 kN
Explain
Determine the magnitude of the pin force at A. Assume W = 535 lb, a = 4.6 ft, b = 3.5 ft, r = 9 in. r W C Answer: A = i a B a A D lb b
Problem- A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm, respectively. An axial load of 12kN is applied on the bar. E= 2 × 10 N/mm². The elongation of the bar will be
Situation 2: The bar AB is being supported by bars at each end. The length and the area for each bar are given. Determine the distance x to where the 100 N load must be applied if the bars must have the same stress. A. Distance x (feet) L-3 ft A= 0.2 in L=2 ft A= 0.3 in 100 N B. 8 ft
Please answer soon
Please answer all, Strength of Materials. Thanks!