3.Calculate and determine the nature of all forces in the bar using the point balance method800 N3 mD.A = SendiC= Rol3 m3 m3 mA=Sendi (Joints) C=Rol (Rollers)

Answered: Image /qna-images/answer/34f0140a-e766-4f93-8fb5-0765fe689f5d.jpg

Answered: 3.Calculate and determine the nature of…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the loading. Forces are positive if in tension, negative if in compression. Answers: AB= i AH = i CD = ܠܚܕܠܚ ܘ ܚ BC = i BH = i CF = 4.6 m DF = i CG= i CH = i GH = i DE = i i EF = i FG = i i B 3.3 m H 22 KN 4.6 m 4.6 m 4.6 m G D 60 KN F 22 KN kN kN kN kN kN kN kN kN kN kN KN kN kN E
please solve it using FORCE METHOD. Thank you. only HANDWRITTEN answer needed ( NOT TYPED)
The change in diameter of the large steel bolt is carefully measured as the nut is tightened. Knowing that the initial diameter d = 50 mm, E = 190 GPa, and ? = 0.27, determine the internal force in the bolt if the diameter is observed to decrease by 0.009 mm after the nut has been tightened. Assume that the supports shown are fixed and rigid. d
asap
Using method of joints, calculate the force in member AC. Input a negative value if compression and positive value if tension. WRITE YOUR ANSWER IN TWO DECIMAL PLACES. 3000 N 40° 2m C B 3m A 4m
The control arm is subjected to the loading shown. The allowable shear stress for the steel pin is τ = 10 ksi. Determine the required diameters of the steel pins at A and C. Write your final answer to the nearest three decimal places.
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. Assume F = 2240 N, a = 3.3 m, b = 6.6 m, 0 = 47° Answers: AB= AC = B AD = Ꮎ Jak a Ө b Ꮎ N Z Z N N D F
SHOW FBD DIAGARM
B1
A hinge supports the truss shown at A and a roller at G.Determine all bar forces using the method of Joints. Summarize answers as shown in the table below.
DETERMINE FORCE (N) OF MEMBER EG in the truss shown. F1 = 214 N %D F2 = 876 N %3D F3 = 435 N a = 38 degree X = 15 m. **Note: for compression, include a negative sign (- ) and for tension, type your answer as is. Input your answer in two (2) decimal places only without the unit. В H A C E G F1 F2 F3
Determine the force in each member of the loaded truss. All triangles are equilateral with side length d. The forces are positive if in tension, negative if in compression. Answers: §§ 8 8 8 8 8 4 ė AB- AG= i BC= i i i i ¡ 1 i i i i B G 7.0 kN KN kN KN KN kN KN kN KN KN 6.2 KN kN KN kN D

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

3.Calculate and determine the nature of all forces in the bar using the point balance method 800 N 3 m D. A = Sendi C= Rol 3 m 3 m 3 m A= Sendi (Joints) C=Rol (Rollers)