Using the Cantilever Method, determine all the member forcesof the frame shown below. Submit your answers in the format where the member forces are written along the corresponding members as illustrated in the short video discussion. Computation of such values may no longer be shown. a= 7 m b= 8 m P= 118 kN ЗР/2 H. 4m D E F 5m a b

Using the Cantilever Method, determine all the member forcesof the frame shown below. Submit your answers in the format where the member forces are written along the corresponding members as illustrated in the short video discussion. Computation of such values may no longer be shown. a= 7 m b= 8 m P= 118 kN ЗР/2 H. 4m D E F 5m a b

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a\ A steel tape has a cross-section of 13 mm*1 mm and weighs 0.122 kg per meter. When supported throughout its length and under a pull of 7 kg and a a temperature of 15° C, its length is 50 m. A line is measured with it and found to de 2560 m. In this measurement the tape was supported at the end only, the pull was 12 kg and the average temperature was 30° C. What is the true length of the line? Take the coefficient of expansion of tape as 12*10 per degree C, E= 2.11*10 kg\cm?. Assume the ends to be at the same level.
Find D and E
3.Statistics of Regid Bodies/ Civil Engineering
Problem 2 For the simply supported beam shown below, determine whether the beam is cracked or un-cracked under the applied loads, use f'e = 25 MPa, if the beam is cracked calculate the bending stresses in the beam using the transformed area method. 20 KN 300 mm 4 kN/m A↓ D 3025 k 3 m 3 m 500 mm - աա St
Solve the given problem. Round off answers in all computations in 4 decimal places. Determine the moment capacity of the beam shown in the figure.
show answer in 3 decimal placesILLUSTRATE/DRAW THE PLANES AND RECTANGULAR COORDINATES AS NEEDED IN THE SOLUTIONS.
Please solve the problem step by step so I can understand. Please show all work.
Note: this is not a graded question please help us to understand how to solve this sample question thank you very much A.) Select the answer that most nearly gives the absolute value of axial force on member ab from the virtual structure for vertical displacement of joint d. choices: 1.25 2.36 0.87 0.21 1.68 1.50 2.00 0.55 note: please base your answer on the given choices thank you for the help
Using either the Portal Method or Cantilever Method, determine all the member forces of the frame shown below. Submit your answers in the format where the member forces are written along the corresponding members as illustrated in the short video discussion. Computation of such values may no longer be shown. a= 7 m b= 9 m P= 113 KN 3P/2 P G a H E b I F с 4m 5m
20 kN 25 kN В 15 kN A E 4 m Başka yönergeler almak için tıklayın Determine the member forces in members AB, BD and AD? (Take AE=1) (If you find a negative value as your final answer, DON'T take absolute, write down the exact value with correct sign!!) (Use. "dot" for decimals and submit your answer with 2 digits) FAB = kN FeD = kN FAD = kN 3 m
Using the Portal Method determine all the member forcesof the frame shown below. Submit your answers in the format where the member forces are written along the corresponding members as illustrated in the short video discussion. Computation of such values may no longer be shown. a= 7 m b= 10 m P= 116 kN ЗР/2 G H 4m P 5m a b
20 kN FBD= FAD = B A KN 25 kN KN C ㅏ 4 m D 20 kN E Click to see additional instructions Determine the member forces in members AB, BD and AD? (Take AE=1) (If you find a negative value as your final answer, DON'T take absolute, write down the exact value with correct sign!!) (Use. "dot" for decimals and submit your answer with 2 digits) FAB = KN 3 m 4 m