A column is constructed using four A992 steel anglesthat are laced together as shown. The length of thecolumn is to be 40 ft and the ends are assumed to befixed connected. Each angle shown below has anarea of A = 2.75 in^2 and moments of inertia of Ix = ly= 2.22 in^4.(Figure 1)2.068 in.0.932 in.0.932 in.2.068 in.CсCCyDetermine the distance d between the centroids C ofthe angles so that the column can support an axialload ofP = 340kip without buckling. Neglect the effect of thelacing.Express your answer to three significant figures andinclude the appropriate unitsXd

A column is constructed using four A992 steel angles that are laced together as shown. The length of the column is to be 40 ft and the ends are assumed to be fixed connected. Each angle shown below has an area of A = 2.75 in^2 and moments of inertia of lx = ly = 2.22 in^4.

A column is constructed using four A992 steel angles that are laced together as shown. The length of the column is to be 40 ft and the ends are assumed to be fixed connected. Each angle shown below has an area of A = 2.75 in^2 and moments of inertia of lx = ly = 2.22 in^4.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Shown in the figure attached is a beam. Given the loading and support condition and assuming that EI is constant for the beam, determine the (a) The equation of the elastic curve, (b) The deflection at the left end of the beam, and (c) The support reactions By and MB.
Express your intermediate answers with FRACTION and simplify your FINAL answers up to TWO DECIMAL PLACES.BOX your FINAL ANSWERS
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 416 mm?, 622 mm?, and 281 mm? respectively.Determine the change in length (in mm) of the bar if P = 27177 N.The moduli of elasticity are 81.33 GPa for bronze ,73.05 GPafor aluminum , and 200.23 GPa for steel . Round off the final answer to four decimal places. Bronze Aluminum ЗР Steel 2P P 4P -0.6 m 1.0 m- 0.8 m
please show all details
A high performance racing plane is to have an aileron control rod made out of unidirectional carbon fibre tubing with the following material properties: elastic modulus E = 90 GPa and compressive failure stress OF,comp= 600 MPa. In order to avoid parts of the internal wing structure the control rod is required to have a bend at the tip as shown in the figure. The rod is L = 400 mm long with an inner diameter of 8 mm and an outer diameter of 10 mm. The length of the bent portion of the rod is = 40 mm . The servo applies a maximum compressive or tensile force of F= 200 N on one end of the control rod as shown in the diagram. The end at which the loading is applied can be considered to be free and the other end of the control rod can be considered to be fixed. Consider the case where the servo applies a compressive force on the tip of the control rod: (i) (ii) X Find the maximum compressive stress in the rod and the maximum transverse deflection of the rod at B. Find the maximum…
Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine the maximum permissible value of T subjected to the following conditions: T, s 90MPA, T. S 65MPA and the angle of rotation of the free end limited to 11°. Use GS 84 GPa and Ga = 27 GPa. %3D %3D 75 mm Aluminum Steel 50 mm 2 m 1.5 m
Show complete solution.
9. If d be the diameter of MS or tor steel bars in mm, the standard weight (in kg) per metre of the bar is 100 (a) 0.00618 d² (b) 0.00618 d (c) 0.00816 d² (d) 0.00816 d
Question 29 An A36 angle bar is used as a tension member connected on both legs with 20 mm . Given that s = 60 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile yielding in the gross area. Write your answer to the nearest whole number. Ag = 1,852 mm2 t = 8 mm
Please write the solution on paper.
Can you help me to solve this question please ? Thank you!
333