3. A homogeneous beam with an overall weight of W is to be connected, as shown below, to 2 cables whose bottom ends are on the similar elevation. What is the ideal ratio of the areas of the rods so that the homogeneous beam will remain level? Aluminum E = 10 x 10° psi L= 4 ft Steel E = 29 x 10 psi L= 6 ft Total Weight = W 3 ft 6 ft 1 ft

3. A homogeneous beam with an overall weight of W is to be connected, as shown below, to 2 cables whose bottom ends are on the similar elevation. What is the ideal ratio of the areas of the rods so that the homogeneous beam will remain level? Aluminum E = 10 x 10° psi L= 4 ft Steel E = 29 x 10 psi L= 6 ft Total Weight = W 3 ft 6 ft 1 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer with a complete solution. Thank you! The roof truss is supported by a hinge at A and a horizontal roller support at B. The wind loads are perpendicular to BC. Determine the reactions at A and B.
Please show a detailed solution and explanation including its FBD. Thank you!
Solve ASAP
The prismatic rod shown is made of a steel that is assumed to be elastoplastic with E = 200 GPa and oy = 280 MPa. Knowing that couples M and M' of moment 525 N·m are applied and main- tained about axes parallel to the y axis, determine (a) the thick- ness of the elastic core, (b) the radius of curvature of the bar. y M 18 mm 24 mm X 'M'
Calcualte the following: Total factored floor load in 2 decimal places, ___ kPa Total factored uniform load on girder GH in 2 decimal places, ___ kN/m Maximum ultimate bending moment at discontinuous end of girder JK to the nearest whole number = ___ kN·m
A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the allowable stresses are Salum = 90 MPa and Spronze=80 MPa, find the maximum weight of the beam that the system can support (in KN). note: please help us in this sample question and it is not a graded question but a practice question thank you
SHOW THE DIAGRAM AND YOUR COMPLETE SOLUTION: statically determinate beam is loaded as shown in the figure below. Determine the following: 1. Determine the force acting in the internal connection. А, 30 KN.m 1.5 m Im B 1.5 m O L=6m 10 KN internal hinged 1.5 m 1.5 m E
2. Determine the force in each member of the platform truss and state if the members are in tension or compression. Approximate each joint as a pin. 8 kN 16 kN 8 kN 3 т 3 т D. 0 000 3 т F 4 m A 4 m Paint X lite
steel The hollow section column, shown in the figure below, has a length of 18 ft, and it is made of steel with a yield strength of 50 ksi. The column is fixed at the bottom and pinned at the top. What is the capacity of this column under a pure compressive loading? |3/4 in 3/4 in 10 in 5 in
Please answer the problem attached image. Using NSCP 2015 ,thank you.
A frame structure is shown below. The links connected below is a bar with a 30mm by 60mm in section. Find the Allowable lad P that can be applied so that the stresses will not exceed 100MPa in tension or 80Mpa in compression.
The answer is close to 60 Ksi. I need help showing the work to get the answer . Please include units. Thanks