A rod with a cross-sectional area of 0.5 in2 is composed of three sections: steel, aluminum, and bronze rigidly attached with each other, aluminum being at the center of the three. Axial loads are applied as follows: 12,000 lbs. going out of steel and 3000 lbs. going out of aluminum. Dtermine the stress in steel, aluminum, and bronze respectively. Draw the free-diagram.

A rod with a cross-sectional area of 0.5 in2 is composed of three sections: steel, aluminum, and bronze rigidly attached with each other, aluminum being at the center of the three. Axial loads are applied as follows: 12,000 lbs. going out of steel and 3000 lbs. going out of aluminum. Dtermine the stress in steel, aluminum, and bronze respectively. Draw the free-diagram.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Portions of a x-in. square bar have been bent to form the two machine components shown. Knowing that the allowable stress is 18 ksi, determine the maximum load that can be applied to each component. (a) 1 in. (b) The maximum load that can be applied to component (a) is The maximum load that can be applied to component (b) is lb. lb.
S=25
1.A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are € E =0.40x10-3 and ɛ =0.3 x 10- determine O and o. Use E = 110 GPa and v=0.35. y y. = Blank 1 MPa Answer in 1 decimal place = Blank 2 MPa Answer in 1 decimal place
The aluminum bar ACDB is rigidly connected to a steel tube in CD. The data is presented in the table. If the load P is equal to 125 kN, determine: The stress of aluminum in segment AC. Answ: 63.66 MPa The stress of aluminum in segment CD. Answ: 13.93 MPa The stress in steel in segment CD. Answ: 39.79 MPa The total deformation of the bar. Answ: 0.29273 mm
4
S=25
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
please answer question below step by step fill in all blanks, charts, stresses, and tresca
two rods attached to a rigid bar AB with negligible mass . A 101 kN load was applied at the end of this bar. The computed stresses for steel and bronze are Blank 1 mPa and Blank 2 mPa respectively.
1. Find the properties of equal-leg angle bar 150 x 50 x 6.0 in metric. 2. Find the full section properties of LC shapes steel bar 100 x 50 x 15 x 3.0 in metric. 3. A stress that lies between the proportional limit and the upper yield point of a steel. What is 5 and 5 Show the relationship uring a graph of mild structural stool
ProbleT = - An aluminum bar has diameter d = 40 mm, shear modulus of elasticity G = 27 GPa, and torque T = 300 N.m. (a) Determine the maximum shear, tensile, and compressive stresses in the bar, and show these stresses on sketches of properly oriented stress elements. (b) Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements. |d=40 mm T= 300 N-m
#2 will upvote to anyone who will answer