A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 416 mm?, 622 mm?, and 281 mm? respectively.Determine the change in length (in mm) of the bar if P = 27177 N.The moduli of elasticity are 81.33 GPa for bronze ,73.05 GPafor aluminum , and 200.23 GPa for steel . Round off the final answer to four decimal places. Bronze Aluminum ЗР Steel 2P P 4P -0.6 m 1.0 m- 0.8 m

A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 416 mm?, 622 mm?, and 281 mm? respectively.Determine the change in length (in mm) of the bar if P = 27177 N.The moduli of elasticity are 81.33 GPa for bronze ,73.05 GPafor aluminum , and 200.23 GPa for steel . Round off the final answer to four decimal places. Bronze Aluminum ЗР Steel 2P P 4P -0.6 m 1.0 m- 0.8 m

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 8ETSQ

See similar textbooks

Similar questions

A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 415 mm?, 636 mm² , and 253 mm² respectively.Determine the change in length (in mm) of the bar if P = 28084 N.The moduli of elasticity are 83.77 GPa for bronze ,71.95 GPafor aluminum , and 204.98 GPa for steel. Round off the final answer to four decimal places. Bronze Aluminum Steel 2P ЗР P. 4P 0.6 m →k 1.0 m 0.8 m Add your answer
A steel bar is connected to an aluminum bar as shown below. At 70 F, the stresses in the steel and the aluminum bars are zero. Calculate the stresses in the steel and in the aluminum when the temperature rises to 120 F. Indicate whether the stresses are tensile or compressive. The properties of the steel and the aluminum are given below. The cross-sectional areas of the steel and the aluminum are the same.
} 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm?. If a tensile load was applied to an aluminum bar to achieve the same lateral (transvers) strain with the former (steel bar), what would be the load? Note: Original dimensions of the two bars are the same (Est = 2.1 x 105 MPa, Eat = 0.703 × 105 MPa, vg = 0.3, vat = 0.33) E = º , v = - Saterat Eaxial Fatuminum™ 3000 N A-500 mm² A=500 mm² Fatuminum=? 3000 N Steel Aluminum
IV. An Aluminum bar AD (see figure) has a cross-sectional area of 250 mm2 and is loaded by forces P1 = 7560 N, P2 = 5340 N, and P3 = 5780 N. The lengths of the segments of the bar are a = 1525 mm, b = 610 mm, and c = 910 mm. (a) Assuming that the modulus of elasticity is E = 72 GPa, calculate the change in length of the bar. Does the bar elongate or shorten? (b) By what amount P should the load P3 be increased so that the bar does not change in length when the three loads are applied? (c) If P3 remains at 5780 N, what revised cross-sectional area for segment AB will result in no change of length when all three loads are applied? A k a B₁ P₁ b C P₂ -P3
Getting measurements from Figure , determine approximate values of the following items for steel with different carbon contents. Use one system of units only as specified by the instructor.a. Yield stressb. Ultimate strengthc. Strain at failured. Effect on modulus of elasticitye. Approximate toughness. Curves may be approximated with a series of straight lines.f. Comment on the effect of increasing carbon content on items a through e above.
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.8 in?, 1.07 in?, and 0.56 in? respectively.Determine the change in length (in inches) of the bar if P = 11280 Ib.The moduli of elasticity are 30092 ksi for steel,12006 ksifor bronze, and 10002 ksi for aluminum. Round off the final answer to four decimal places. Bronze Steel Aluminum 2 ft 4 ft 3 ft P 2P 3P 4P
A 19-mm reinforcing steel bar and a gauge length of 75 mm was subjected to tension, with the results shown in Table Using a computer spreadsheet program, plot the stress–strain relationship. From the graph, determine the Young’s modulus of the steel and the deformation corresponding to a 150-kN load.
SOM 2. Show your complete solution. ( I know the answers but I need the detailed solution) Given answers: Axial Stress of Copper= 1770.791 psi Axial Stress of Steel = 2956.655 psi Axial Stress of Brass = 1577.946 psi
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b I Steel: A 900 mm Bronze: A E 200 GPa E 83 GPa L-2.0m L=1.5m What is the value of P without exceeding the allowable stress of steel, in KN? 230 250 280 340 1200 mm
A cylindrical bar of steel 9.9 mm (0.3898 in.) in diameter is to be deformed elastically by application of a force along the bar axis. Determine the force that will produce an elastic reduction of 3.0×10-3 mm (1.181 ×10-4 in.) in the diameter. For steel, values for the elastic modulus (E) and Poisson's ratio (v) are, respectively, 207 GPa and 0.30. i N
The figure above are two rods attached to a rigid bar AB with negligible mass . A 68kN load was applied at the end of this bar. The computed stresses for steel and bronze are GIVEN THAT MN=68kN
Figure shows a beam made from bronze subjected to a 3.5 kN.m bending couple and its respective tensile properties. 1) Determine radius of curvature for the beam, ρ