Consider the T-beam shown in (Figure 1). Suppose thata = 80 mm, b=160 mm, c = 10 mm.Figure<1 of 1Determine y, which locates the centroidal axis x' for the cross-sectional area of the T-beam.Express your answer to three significant figures and include the appropriate units.y =SubmitPart BIT' =SubmitPart CValueDetermine the moment of inertia I.Express your answer to three significant figures and include the appropriate units.Request AnswerIy' =ValueRequest AnswerUnitsValueUnits?Determine the moment of inertia Iy'.Express your answer to three significant figures and include the appropriate units.Units??

Given Data Determine a. Location of centroid x' - axis. b. Moment of inertia (Ix'). c. Moment of…

Consider the T-beam shown in (Figure 1). Suppose that a = 80 mm, b = 160 mm, c = 10 mm. Figure of 1 of 1 > Determine y, which locates the centroidal axis x' for the cross-sectional area of the T-beam. Express your answer to three significant figures and include the appropriate units. y = Submit Part B I₂ = Value Submit Part C Determine the moment of inertia Ir. Express your answer to three significant figures and include the appropriate units. Request Answer Iy' = μÅ Value Request Answer Units μА Value Units Determine the moment of inertia Iy'. Express your answer to three significant figures and include the appropriate units. ? Units ? ?

Consider the T-beam shown in (Figure 1). Suppose that a = 80 mm, b = 160 mm, c = 10 mm. Figure of 1 of 1 > Determine y, which locates the centroidal axis x' for the cross-sectional area of the T-beam. Express your answer to three significant figures and include the appropriate units. y = Submit Part B I₂ = Value Submit Part C Determine the moment of inertia Ir. Express your answer to three significant figures and include the appropriate units. Request Answer Iy' = μÅ Value Request Answer Units μА Value Units Determine the moment of inertia Iy'. Express your answer to three significant figures and include the appropriate units. ? Units ? ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve the given problem. Round off answers in all computations in 4 decimal places. Determine the moment capacity of the beam shown in the figure.
please answer this. thank you.
Q.37 Water is moving through a pipe. The velocity profile at a particular section is given mathematically as V = v- (1) (²²-2²) 4μ 4 where v = velocity of water at any position r B: = constant μ = viscosity of water d = pipe diameter r = radial distance from centreline of pipe (i) What is the shear stress at the wall of the pipe due to the water? (ii) What is the shear stress at a position r= d/4? (iii) If the given profile persists a distance L along the pipe, what drag is induced on the pipe by the water in the direction of flow over this distance?
A block of mass M is hit by a horizontal water jet at a speed V. Product of the impact, the block begins to slide at speed U on a horizontal plane whose coefficient of kinetic friction is μk. Consider that the jet has an area A and its density is ρ. All the necessary data are indicated on the figure. i) After a certain time, the forces on the block balance out. Determine the velocity U∞ (terminal velocity) of the object in this condition
1) A block (mass mi) can move horizontally on a smooth surface. A homogeneous rod (mass m2) is connected to the block by a pin. The rod is displaced from its equilibrium position and then released. Find the equations of motion for the special case mi = m2. (mi is the last two digits of the student number for example if student ID is 102560332 then m-32 kg. If the last two digits of the student number is 00 then mi=12 kg) 2a m2
Since answers are already given, I only need the solutions for 3 and 4.
1. The following equation describes the relationship between the maximum deflection of the end of a beam and the applied load. PL3 = 3EI a) If ð is the maximum deflection in inches, L is the length of the beam in inches, P is the load in pounds, and E is the Young's Modulus in pounds/in?, find the units for I (moment of inertia). b) The measured deflection for a specific beam under loading is measured to be .01 in. Convert this to millimeters.
The object W1 in the figure is at an angle of 45 to the horizontalIt is based on its frictionless surface at point B.Point A is articulated (fixed support) and ground frictionSince (μ = 0.3) body W2 is a surfaceWhat should be the weight of W1 that will cause it to start? W2= 38 [kN]sin45=cos45=0.7