using tape standardiz ull of 10kg. The recorded distance was found out to be 430.60 meters. At the time of neasurement the temperature was 20°C and the pull exerted was 16 kg. The weight of one ubic cm of steel is 7.86kg. Use E= 2x10 kg/cm², a=7x10-7/°C ) Compute the actual length of the tape during measurement. ) Compute the true length of each side of the rectangle. =) Compute the true area.

using tape standardiz ull of 10kg. The recorded distance was found out to be 430.60 meters. At the time of neasurement the temperature was 20°C and the pull exerted was 16 kg. The weight of one ubic cm of steel is 7.86kg. Use E= 2x10 kg/cm², a=7x10-7/°C ) Compute the actual length of the tape during measurement. ) Compute the true length of each side of the rectangle. =) Compute the true area.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ngr. Beleric measured a distance line using a 20m length of stainless steel tape measure. The line's length was determined to be 396.84meters.The temperature was 10 oC during the measurement, and the tape was supported on both ends.The tape has a cross sectional area of 7.20mm2 and a modulus of elasticity of 200GPa. The tape is 0.095 kg/m in weight. k = 11.6 x10-6 m/C If the engineer determined the lengths of the Temperature correction, Pull correction, and Sag Correction to be 1,197.23μm, 285.53 μm, and 2.23 mm, per segment, Calculate the 20m tape's standard pull in kilograms.
Given: • Rod A: Length = 40mm Rod B: Length = 60mm Determine: ● ● Area = 3 cm x 3 cm Area = 4 cm x 4 cm Stress in each rod. Deflection of rigid beam at point D D 0.5m B 0.5m 100KN E = 200 GPa E = 200 GPa A + RIGID CEAM
A rigid horizontal slab is attached to two identical copper rods. There is a gap, A = 0.18 mm between the middle bar, which is made of aluminium and the slab. Neglecting the mass of slab, calculate the stress in each rod when temperature of the whole assembly is increased by 85°C and choose the correct options. Use the following data: A(mm) arC) E(GPa) Each copper rod 500 16.8 x 10 120 Aluminium rod 400 23.1 x 10 70 750 mm A Finally, copper will be under tension. Correct Option B Both copper and aluminium will be free i.e. without any stress. Stress in copper will be 6.69 MPa (Magnitude wise) Correct Option Stress in aluminium will be 16.7 MPa (Magnitude wise) Correct Option Coppe Aluminium Coppe
A baseline was measured using a 100m tape which is standardized 15oC with a standard pull of 10kg. The recorded distance was found out to be 430.60 meters. At the time of measurement the temperature was 20oC and the pull exerted was 16 kg. Determine the true length of the base if the weight of one cubic cm. of steel is 7.86 gr. Weight of tape is 2.67kg, E = 2 x 106 kg/cm2, K = 7x10-7 m/oC.
A flat steel bar, 29 mm wide by 5 mm thick and 1.5 m long, is bent by couples applied at the ends so that the midpoint deflection is 23 min. Compute the maximum stress in the bar. Use E = 200 GPa. Answer must be in MPa. Next * Previous
A beam shown below, 200mm wide by 350mm deep, is loaded as shown in figure below. Determine the stress in a fiber 50mm from the top of the beam at point B. 50kN A 20 купи RI B 2M X 30KN/M TITT. 4m 20 km. ITTJ 2m + <
Q2/ The rigid, horizontal slab is attached to two identical copper rods. There is a gap A=0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 85°C. Use the following data: Each copper rod Aluminum rod A (mm²) 500 400 a (°C) 16.8 x 10-6 23.1 x 10-6 E (GPa) 120 70 Copper TA Aluminum Copper L=3m A= 1500 mm E=120 GPa a = 16.8 x 10-C Copper -750 mm-
Fig.( a) shows a steel wire 1 mm diameter is stretched horizontally between two fixed points apart. A vertical load applied at the mid span of the wire causes a vertical displacement of 45 of the point of application of the load applied. What will be the stress induced in the wire and load applied? Neglect the weight of the wire. Take E for the wire material as 200 GN/m². F L 1 m P S N -1 m- M
Situation H. A 100m tape weighing 3kg that is standard at 10°C and a 30N pull is used to measure a distance which was recorded to be 3300m. Condition during survey: Modulus of Elasticity Temperature Pull 200 GPa 15 °C 40N Coefficient of 11.6 x 10-/°C Thermal Expansion 16. Determine the error due to sag. 17. Determine the error due to change in temperature. 18. Determine the error due to change in pull. 19. Determine the correct distance between the two points.
Wire BC has a diameter of 0.10 in. And its material has the stress-strain characteristics shown in the figure. Determine the vertical displacement of the handle D if the pull on the handle is slowly increased and reaches the magnitude of P = 655 lb. o (ksi) 40 pulg 80 70 B 50 pulg - 30 pulg € (pulg/pulg) 0.007 0.12
Determine the proportional shear stress for a material that has a modulus of rigidity of 30 GPa and proportional shear strain of 0.0001. Select one: O a. 30 x 10 Pa © b.0.003 Pa C. 30 x 10 Pa 13 Pa G d. 30 x 10
The cross-section of the beam in the picture is welded from two flat steel 100x20x2000 mm. So L = 2000 mm. The material is S355 J2 G3 (EN 10025). What is the certainty compared to the following? q0 = 19.4 kN/m Correct answer 4.07