1.1 For the structure shown in Figure P1-1 F₂2 20 in Member 1 F3 15 in- Member 2 F 10 in Member 3 Areas for all members =2 sq. in Figure P1-1 (2) Determine the structural stiffness matrix by combining individual elemental stiffnesses.

1.1 For the structure shown in Figure P1-1 F₂2 20 in Member 1 F3 15 in- Member 2 F 10 in Member 3 Areas for all members =2 sq. in Figure P1-1 (2) Determine the structural stiffness matrix by combining individual elemental stiffnesses.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 2.5 in. and a thickness of 0.75 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.7 in. and a thickness of 0.75 in. The supports at A and C are rigid. Assume h1=2.5 in., h2=1.7 in., L1=31 in., L2=46 in., and Δ=Δ= 0.04 in. (A) Determine the lowest temperature, Tcontact, at which the two bars contact each other. (B) Find a geometry-of-deformation relationship for the case in which the gap is closed. Express this relationship by entering the sum δ1+δ2, where δ1 is the axial deflection of Bar (1), and δ2 is the axial deflection of Bar (2). δ1+δ2= _____in. (C) Find the force in the Bar (1), F1, and the force in Bar (2), F2, at a temperature of 225oF. By convention, a tension force is positive and a compression force is negative. IN KIPS (D) Find σ1 and σ2,…
If the posson ratio of elastic material is 0.453 the ratio of modulus of rigidity to Young modulus
For the structure shown with loading symbolised as (1) and (2), what is the stiffness matrix?
Which of the following is false regarding factor of safety in the design of structures? a. It considers uncertainties in the material properties. b. A higher factor of safety is preferable in designing safe structures c. It should not be less than 1 to ensure the structure’s safety. d. It considers changes in the loading pattern on the structure. Which of the following occurs when the value of Poisson’s ratio is doubled and the modulus of elasticity is kept constant? a. The lateral deformations experienced by the material is halved b. The volume of the material will remain constant when subjected to external forces c. The elastic region of the shear stress-strain diagram would be less steep d. The material can withstand higher amounts of stress before permanent deformations occur
The degree to which the theoretical value of stress concentration is actually reached is called as
An element in the plane stress is having the larger principal stress (tension) as 30 MPa and it is subjected to stresses, Ox = 50 MPa, 40 MPa then what will be and Txy the value of the stress oy? (in MPa) =
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 50 x 10 mm while -3 those at CD decrease 60 x 10 nm in the 210 mm gage length Using E 140 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a 50 mm, b 130 mm, and c 80 mm. gage length la mm omm c mni
For material, the modulus of rigidity is 100 GPa and the modulus of elasticity is 250 GPa. The value of the Poisson's ratio is
For the structure shown in the figure, all of 1, El and L are of respective unit values. The equivalent stiffness constant for the structure is 1, EI de Grà K=3
19 This theory explains that the elastic failure occurs when energy per unit volume in a strained material reaches the value of the strain energy per unit volume at the elastic limit point in the simple tension test. Also, the maximum energy which a body can store without deforming plastically is constant for that material irrespective of the manner of loading. What do you call this theory Bulk Modulus Volumetric strain Hook's Law Elastic Theory Strain energy theory
1. At a temperature of 5°C, a 3-mm gap exists between the end of polymer bar (1) and support A as shown. Bar (1) is 50 mm wide and 20 mm thick (E = 800 MPa, a = 140 x 10-6/°C). Bar (2) is 75 mm wide and 25 mm thick (E = 2.7 GPa, a = 67 x 106/°C). The supports at A and C are rigid (i.e., fixed). Determine: a) the temperature at which the normal stress in bar (2) will be equal to -3.0 MPa, and b) the lengths of the two polymer bars at this temperature. (1) 3-mm gap 50 mm 500 mm B 75 mm 400 mm (2)
The state of stress on an element is as shown in the figure. If E=2×10 N/mm² and Poisson's ratio = 0.3, the magnitude of the stress o for no strain in BC is 80 N/mm² G B C 80 N/mm²