Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at locationA to another pulley at location B. Assume the tensions In the belt at pulley Bare T, and T2, where T Is15% of T2.NOTE: This is a multi-part questlon. Once an answer is submitted, you will be unable to return to thispart.T210.018.0"Bearing at O500 Ib12.0pulley diameter = 8.0"75 IbT1pulley diameter = 10.0"Bearing at CSut163 kpslSy117 kpslMaterlal1050 Q and TUsing the DE-Goodman criterla and a design factor of 1.5, calculate the diameter based on the shaft's loadings and yourguess for the shaft's dlameter at the critical location. What Is the shaft diameter? Assume the notch radlus to be 0.02In. (You must provlde an answer before moving to the next part.)The shaft dlameter Is|1.3146| In.The factor of safety agalnst ylelding Is3.75

Answered: Image /qna-images/answer/c0f9f7cb-37ec-48e1-9c0b-fcfc000e7661.jpg

Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at location A to another pulley at location B. Assume the tensions In the belt at pulley Bare T, and 72. where T, is 15% of T2. NOTE: This is a multi-part question. Once an answer Is submitted. you will be unable to return to this part. T2 10.0 18.0 Bearing at o 500 Ib 12.0 pulley diameter = 8. 75 Ib T1 pulley diameter = 10.0 Bearing at C

Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at location A to another pulley at location B. Assume the tensions In the belt at pulley Bare T, and 72. where T, is 15% of T2. NOTE: This is a multi-part question. Once an answer Is submitted. you will be unable to return to this part. T2 10.0 18.0 Bearing at o 500 Ib 12.0 pulley diameter = 8. 75 Ib T1 pulley diameter = 10.0 Bearing at C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2/ A compound steam engine develops 250 kW at 80 r.p.m. The coefficient of fluctuation of energy as found from the turning moment diagram is to be 0.15 and the fluctuation of speed is energy as feed 1% of the mean speed. Find the weight of the flywheel required, if the radius of gyration is 1.5 m. T
1- A bush roller chain drive is used to transmit 4 kW of power from the driving shaft on a hydraulic motor runs at 1200 r.p.m to the driven shaft which runs at 350 r.p.m. The drive is required to operate continuously with drop lubrication and driven machine is such that load can be regarded as fairly constant. Design the chain drive by calculating leading dimensions, number of teeth on the sprockets taking into account that the available distance between the two shafts centers is 400mm + 4% no more no less.
A marine engine cylinder has a compression ratio (r) of 9.5, a clearance volume of 650 cm3and a piston stroke length of 675 mm. What is the bore diameter in millimetres (mm) for the engine cylinder. Give your answer to the nearest millimetre mm.
! Required information A steel shaft is to be designed so that it is supported by roller bearings. The basic geometry is shown here, with L = 325 mm, a = 32.5 mm, and F= 3400 N. To achieve a reasonable bearing life, the allowable slope at the bearings is 0.0025 mm/mm. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. With the diameter known, what is the maximum deflection of the shaft? The maximum deflection of the shaft (ymax) is - mm.
Please don't provide handwrittenh solution.
1-Show how the roughness is indicated for a Surface to be coated, obtained by any production method with N6 showing max. and min roughness. 3- gearing is suitable for two shafts at 90°. : Draw five turns of a compression spring of wire diameter 6mm, pitch 12 num and outside diameter of 38mm.
Item 1 used to intermittently operate a piece of equipment at the end of a lifter arm. The lifter is in contact with the highest point of the cam at the instant shown and the lifter is constrained to move only in the vertical direction. The cam has a radius of r = 4.5 in and is rotating about point O, which is offset from the center by a distance c = 3.0 in. The cam's angular position is measured from the positive x axis and is positive clockwise. The angular velocity and acceleration are positive clockwise. (Figure 1) Figure (0,0 36°F Clear r W 1 of 1 Par Find align Expr Vie Omin Subn Provide Feedb
Please help. Written on paper not typed on computer or keyboard please. Need help on all questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
None
A taper roller bearing used in a windmill has a dynamic load capacity of 26 kN. The desired life for 90% of the bearings is 8490h and the speed is 350 rpm. The rated bearing life(L10) in millions of revolutions is . O a. 509.40 O b. 178290.00 O c. 17829.00 O d. 178.29 In a machine, the maximum torque transmitted by a shaft exceed by 23 % the actual torgue. A power of 3 kW has to be transmitted to another unit at a speed of 650 rpm. What should be the value of Maximum torque ? The maximum torque transmitted in N-m, When a component is subjected to fatigue loading, the endurance limit is the criterion for failure Select one: O True O False If "g" is the notch sensitivity, K, fatigue stress concentration factor, and k, the theoretical stress concentration factor. Identify the correct relation relating to these factors. (Ke-1)+(q)=(Kf - 1) O b. (K-1)=(Kf -1)*q O a. O c. (K-1)*(q)=(Kf -1) O d. (K,-1)-(q)=(Kf -1)