Solve fast please and if you don't know please skip it no data missing QI: A double-threaded 30-mm power screw is 30 mm in diameter with a pitch of 6 mm. The coefficients offriction are 0.05 for the collar and 0.08 for the threads. The frictional diameter of the collar is 40 mm. if T-18N.m:1- Find the A vertical load on the screw, the torque used to lower the load and screw efficiency.2- Compute all the stresses on the screw body that will cause by the load.

Answered: Image /qna-images/answer/83e5c33b-d354-4a09-afdd-f326e8d387da.jpg

Answered: QI: A double-threaded 30-mm power screw…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

AutoCAD is one of the ready-made programs that help workers in the field of design and engineering drawing because OThe possibilities it provides to facilitate the design process. OThe non-possibilities it provides to facilitate the design process. OThe possibilities it non-provides to facilitate the design process.
Posted below is a picture of a data table and a diagram of an experiment. In the experiment you rolled a marble down a ruler ramp off the end of a coffee table to observe projectiles and conservation of energy. You do 3 trials for each initial height. Each height is measured in meters. h= initial height of marble off of table Y= height of table off floor X= horizontal distance marble goes from edge of table to where it strikes the floor a) use the table to find information you need to solve for theoretical range and % of error in measured range.
I need the answer as soon as possible
1) A low-friction cart is placed between two identical springs attached to rigid walls. If you push the cart against one of the springs and release it, it will continue to move back and forth between the springs. www Draw a force-time graph showing the sum of the horizontal forces exerted on the cart as it moves back and force between the springs. Scientific Abilities Is able to construct a force diagram Missing No representation is constructed. Inadequate FD is constructed but contains major errors such as incorrect mislabeled or not labeled force vectors, length of vectors, wrong direction, extra incorrect vectors are added, or vectors are missing. Needs Improvement FD contains no errors in vectors but lacks a key feature such as labels of forces with two subscripts or vectors are not drawn from single point, or axes are missing. Adequate The diagram contains no errors and each force is labeled so that it is clearly understood what each force represents. Explain whether or not this…
4- Which of the following lines is used to: show the axis of symmetry for feature indicate path of motion part, and show the location for bolt-hole circles and other circular or patterns a) O Folding b) Vision C) Center d) Hidden Boş bırak KOnceki 4/20 Sonraki> Каpat VSinav Bitir
Please help answer all parts, thanks
6. Write one block of code to perform the indicated operation. Assume the location is X2.0, Y2.0, and the depth is Z-1.5 for each operation. 1) Drill with dwell of 0.2 seconds 2) Peck drilling cycle with a 0.15" peck depth 3) Chip breaker with a 0.15" peck and full retract every 0.6" 4) RH tapping cycle for 14-16 NC thread; define a spindle speed and feed 5) Bore a hole with the tool being retracted manually
type theory in ms word and draw fig on A4 pages
Please draw the right side view. Don't copy from anywhere else. Please write the dimensions as well.
INSTRUCTIONS: Please write clearly and understandable way. Write all the corresponding GIVEN with their corresponding symbols and units. List all the MISSING/REQUIRED, and list all the FORMULA that will be used. • DRAW/ILLUSTRATE THE DIAGRAM/CIRCUIT OR DRAWINGS that is related to the problem, IF POSSIBLE, which is HIGHLY REQUIRED. The CONVERSION calculations with their corresponding symbols and units is required. The problem's SOLUTION must be solved in a step-by-step, no shortcut, again, with their corresponding symbols and units. • BOXED the Final Answer. PROBLEM: The compressor of a large gas turbine power plant receives 12kg/s of surrounding air at 95kPa and 20°C. At the compressor outlet, air exits at 1.52MPa, 430°C, Determine the flow energy requirements in MW. a) 1.412 b) 2.42 c) 1.01 d) 1.614
solve questions (7, 8 and 9)
The answer is one of the options below please solve carefully and circle the correct option Please write clear .

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS