Instructions:• Create a step by step and detailed explanation on how to solve the problem attachedbelow.Create a script-like document like how you would explain this in a video presentation.Explain every single step with full details.Think of it that you have a youtube channel and you are explaining this problem step bystep and on this document you will put the transcript of your video presentation exceptthere is no video presentation only the transcript is needed.• Include complete solution and what formulas are used.PROBLEM:Given is a thin-walled tube with the following data:Wall thickness- 2mmABC is a sector with a radius of 100 mmAOD & COD is a triangleTorque is 800 N.mLength of the thin walled tube is 2 m.Use G=24 GPa for aluminiumB30⁰Determine the following:a. Enclosed Areab. Perimeter of the thin walled tubec. Shear flowd. Shear stresse. Angle of twist

Answered: Image /qna-images/answer/6048373e-a748-4b4a-a6de-7434aed97d2e.jpg

Given is a thin-walled tube with the following data: Wall thickness- 2mm ABC is a sector with a radius of 100 mm AOD & COD is a triangle Torque is 800 N.m Length of the thin walled tube is 2 m. Use G-24 GPa for aluminium Determine the following: a. Enclosed Area b. Perimeter of the thin walled tube c. Shear flow d. Shear stress e. Angle of twist D

Given is a thin-walled tube with the following data: Wall thickness- 2mm ABC is a sector with a radius of 100 mm AOD & COD is a triangle Torque is 800 N.m Length of the thin walled tube is 2 m. Use G-24 GPa for aluminium Determine the following: a. Enclosed Area b. Perimeter of the thin walled tube c. Shear flow d. Shear stress e. Angle of twist D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2: Figure (2) shows an isometric view of a crankshaft that is actuated by the vertical force acting at the end of the crank (267N). The diameter of the crankshaft is (10 mm). Figure (2) 254 mm 102 mm Find: 152 mm 1. Principal stresses at points B & C. 2. Select a suitable material for the crankshaft at the Rc worse condition. 76 mm 267 N -127 mm- RA
Figure 1 shows a composite shaft ABCD acted upon horizontal forces. The moduli of elasticity and the cross-section areas of the segments of the shaft are also provided. Eal = 70 GPa AAB = 58 mm2 Ecu = 126 GPa Est AcD = 39 mm2 = 200 GPa ABC = 77 mm2 %3D %3D Copper 20kN 8 kN Aluminum Steel 7 kN A B 20kN D 8 kN 450 mm 300 mm - 400 mm Figure 1: Axially loaded composite shaft 2.1. Construct the diagram of internal normal forces for each cross-section of the shaft (6) 2.2. Calculate the displacement of the point C with respect to the fixed-point A. (3) 2.3. If the shaft must have one uniform diameter, determine the required minimum diameter of the shaft if the normal yield stress in the composite shaft must not exceed 450 MPa with a factor of safety equal to 1.8. (11)
Solve this Carefully, Write clearly and Circle the Final answer for Tmax with the correct units and for Part B T = with the right units
For the two-cell tube, the rate of twist is 5 degree/meter. G=20 GPa, if a is 10 cm and t equals to 4 mm, find the maximum shear stress in the walls.
A link of a valve gear has to be curved in one plane, for the sake of clearance. Estimate the maximum tensile and compressive stress in the link if the thrust is 2500 N. (Cam bridge) ANSWER: maximum tensile 38.0 MN/m2; maximum compressive 46.0 MNIm2. Please show the solution to get the answer.
1- The shaft shown in the below Fig. consists of a 75-mm diameter aluminum segment rigidly joined to a 50-mm diameter steel segment. The ends of the shaft are attached to rigid supports. Calculate the maximum shear stress developed in each segment when the torque T = 1130 N.m. is applied. Use G = 28 GPa for aluminum and G = 83 GPa for steel. %3D %3D Aluminum Steel 75 mm diameter 50 mm diameter 1130 N.m Tal 1st 2 m 1 m
1. Calculate the maximum stresses to occur in the hole and groove (groove) areas in the plate below, whose geometry and the applied force are known. 200 mm d = 30 mm 5000 N 5000 N t= 25 mm r= 15 mm
r2, E, , E L2 Two aluminum circular shafts (E=70GPA) are mounted according to the figure. The two shafts have the following dimensions: r1 = 6.9mm r2 = 11.1mm L1= 1.52m L2 = 1.29m. If the load applied is P = 2.1 kN, what is the displacement at the point of application of P in mm (accuracy of 5%)?
100 kip 10 kip ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of the following are closest to the principal stresses in the shaft? 01 = 31.8 ksi 02 = 76.4 ksi = 94.0 ksi 02 = -62.1 ksi O0g - 14.3 ksi 02 = -6.37 ksi Oo= 7.96 ksi 02 = 9.55 ksi
include FBD and complete solution
i need the answer quickly
I need neat Handwritten Solution. Answer: 1.07