Upon completion of the Reynolds experiment, we had this information. The tube diameter was 0.03 m, the flow rate 21*10^-6 Q (m ^ 3 / s) and the lamellar bisection type 'Find Re, viscosity and velocity m / s at a temperature of 26 ° C for water.

Q: A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see…

A: Fluid relative density = 0.88 PA = 150 KPa PB = 225 KPa ZA = 9.8 m ZB = 0 m

Q: Compute the linear velocity at each point (m/s),

A: Given Data: The temperature of stack is, T=279°F=279+131.372 K=410.372 K. The static pressure of…

Q: In a wind tunnel lab, the pitot tube is located at the height of 2 m, the measured static pressure…

A: To obtain the solution to the given question, we must first calculate the pressure at a height of 1…

Q: Q2/ Put a Circle around the correct Answer: 1/ Dimensions of discharge coefficient Cd are: a)…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: certain garden hose is advertised to be able to deliver 550 gallons of water per hour. If the hose…

A: Given:Q=550 gallons/hr =0.000578327 m3/sL=50 feet =15.24 md=58 in =0.015875 mμ=1.002*10-3 Kg/m.s

Q: This statement is for Questions 4-6: An engineer claims that flow of SAE 30W oil, at 20°C, through a…

A: An engineer claims that flow of SAE 30W oil, at 20°C, through a 5-cm (0.05 m)-diameter smooth pipe…

Q: a caloulaTE THE Velocire OF THE PlUID INSIDE THE TUBE. b) CaloulATE THE HeiGHT DIFFERENCE l To THE…

A:

Q: =// A rotary filter is required for the filtration of a slurry to produce 10 m' in 3500 §, the…

A:

Q: Choose "True" or "False" for the following: [1 1. The flow is assumed isentropic when it subjected…

A: A process is said to be reversible/Ideal in which system returns to its original state without…

Q: Compute the volumetric gas flow in the duct (m3/s)

A: Pitot tube Pitot tube is a flow measurement device used to measure fluid flow velocity. Pitot tube…

Q: Q5/ Oil flows in a 0.3 (m) diameter pipe with a flow velocity of 2.7 (m/s). The physical properties…

A: As per given question we have determine  1- The value of Reynold's Number Re and Mention the Type of…

Q: 04: For the piping system, compute pressure at A, and mid pipe 2. If pipe (3) & pipe (4) havi equal…

A:

Q: A thin-plate orifice is used to measure water flow rate. The water temperature is 27 C and a mass…

A:

Q: The maximum velocity with which a fluid 3. having density of 90kg/m and viscosity 0.1 Ns/m2 can flow…

A:

Q: CONSIDE THE PRESSYRE DROP FOR STEADY, INCOMPRESSiole visous Flow in A STRAIGIT PiPE: Ap. (R- ½) THE…

A:

Q: When crude oil (r.d = 0.855, µ = 71.8*104 Pa. s) flows in a 50 mm horizontal pipeline at 4.5 m/s, a…

A:

Q: Consider a two-dimensional flow which varies in time and is defined by the velocity field, u = 1 and…

A: Find outDoes the fluid element experience angular rotation? Thus, state whether the flow field is…

Q: Fluid originally flows through a tube at a rate of 110 cm3 /s. To illustrate the sensitivity of flow…

A: Given data Volume flow rate, Q1 = 110 cm3/sPressure drop, Px1 = 2.5Radius of tube = rx1 = 0.14Length…

Q: The pressure difference between two points in pipe due to turbulent flow depend on velocity,…

A: ∆P=fV,D,μ,ρ,ε,L

Q: Vortex shedding can be used to design a vortex flowmeter(Fig. 6.34). A blunt rod stretched across…

A: Given:                 The diameter of pipe, D = 5 cm = 0.05 m The sensor diameter, d = 8 mm = 0.008…

Q: DETERMINE THE PRESSURE TO HAVE A DISTANCE: 600m CONSISTENT AND COMPATIBLE FLOW RATE Raver ELEVATION:…

A: Given: Total length of the pipe: →L=600 m Height of the water tank from the river surface: →H=100 m…

Q: Water at 20°C flows through a 9 cm diameter pig as in Fig. The total length of pipe between flange…

A: Diameter = 9 cm Length = 75 cm Mass flow rate = 32.67 kg/s P1 = 73 kpa  P2 = 41 kpa

Q: We want to measure the flow rate of water at 20 C by a thin plate orifice. The pipe diameter…

A:

Q: On a single plot, plot three curves that show the relationship between the pressure generated by the…

A:

Q: A viscous fluid of density 900 kg/m3and viscosity 0.3 Pa.s flows in a horizontal smooth pipe of…

A: Note: According to policy only first three questions can be answered so resubmit for complete…

Q: Figure 2. Determine the pressure at point I if: a) Viscous effect is neglected b) The only losses…

A:

Q: Hot oil is cooled in a double-tube counter-flow heat exchanger. 2 cm diameter copper inner wall…

A: Inner diameter = 2 cm Outer diameter = 3 cm Mass flow rate of water = 0.5 kg/s Mass flow rate of oil…

Q: Q2 .. h, are 12m. The pump efficiency is 79%, and the pump is driven by an electric motor. A pump…

A:

Q: 7. Using the velocity distribution for a laminar, incompressible flow of a Newtonian fluid in a long…

A: Given, Fluid density = ρ = 300 kg/m3 Dynamic Viscosity = μ = 1 x 10-4 Pa-s Cross sectional area of…

Q: In the orifice and Jet flow experiment, the following data were collected. Water level =30 cm ,…

A:

Q: In a steady incompressible two-dimensional flow the velocity vector in m/s is given as: V = (6x-6y)i…

A:

Q: A fluid flow is given by V = 8x³i — 10x²yj. Find the shear strain rate and state whether the flow is…

A: Given data V=8x3i-10x2yj Here, V represents the fluid flow rate. From the above expression,…

Q: Q1. Complete the following: Theory states that if: Re 3000 ..... 2000 < Re < 3000 .......

A: If( Re is less than 2300) flow is laminar flow , when fluid flow through pipe    If ( Re is greater…

Q: A piston-cylinder is producing a viscous oil flow, which has the flow rate of Q, radius R=1.5 mm,…

A:

Q: A particular flow meter allows the volumetric flow rate Q to be calculated from a measured pressure…

A: Given: The flow rate is Q∝∆P. The uncertainty in Q is dQQ=0.25%.   The above equation is,…

Q: For the figure shown below with the accompanying data table, what is the approximate flow in pipe 1…

A:

Q: Describe the methodology for obtaining the pump curve in a project, where data are collected at five…

A: A pump curve is a graphical representation of a pump's performance based on testing conducted by the…

Q: 1. Below is a simple setup of measuring flow velocity using a pitot tube. Which height is useful for…

A: 1) From the pressure balance between the 1 and 2, p1-ρgh2+h3=p2-ρgh1+h2+h3p2-p1=ρgh1 From…

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.