In the orifice and Jet flow experiment, the following data were collected. Water level =30 cm , Volume V = 44.1 L was collected in time 32 seconds, orifice diameter = 6 mm, X, = 50 mm , X, = 100 mm, X, = 150 mm, X, = 200 mm, X, = 250 mm %3D %3D = 3 mm , Y, = 10 mm, Y, = 22 mm, Y, = 38 mm, Y = 63 mm %3D What is the discharge coefficient?

In the orifice and Jet flow experiment, the following data were collected. Water level =30 cm , Volume V = 44.1 L was collected in time 32 seconds, orifice diameter = 6 mm, X, = 50 mm , X, = 100 mm, X, = 150 mm, X, = 200 mm, X, = 250 mm %3D %3D = 3 mm , Y, = 10 mm, Y, = 22 mm, Y, = 38 mm, Y = 63 mm %3D What is the discharge coefficient?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Needs Complete typed solution with 100 % accuracy.
Air with density of 1.225 kg/m^3 and viscosity of 1.789 x 10^-5 kg/m-s flows in a wind tunnel, the wind tunnel spped is measured with Pitot tube probe. For a certain run, the stagantion pressure is measured to be 472.6 Pa gage and the statric pressure is 15.43 Pa gage. Calculate the wind tunnel speed.
Please show how to solve parts a, b, and c shown below. The topic is fluid mechanics. Thank you.
1. A piston-cylinder is producing a viscous oil flow, which has the flow rate of Q, radius R=1.5 mm, and stroke L-5 mm. The fluid density is p = 800 kg/m³ and the viscosity is μ = 0.5 Pa-s. The pressure to drive the flow is p=6.25 Pa. a. How many non-dimensional groupings can be obtained? Derive them. b. If the flow transitions at Re = PV(2R) =2300. Is the generated flow laminar or turbulent given Q=20 mL/s? LL c. Assume the pressure gradient is uniform on the cross-section and can be calculated using OP=-. The velocity profile in the cylinder is u(r) = ax - [1-(²]. Sketch the velocity profile. Calculate the shear stress at the R² ap 2UÔI cylinder wall and label the direction. d. Calculate the flow rate Q with the velocity profile in (c).. e. If the shear stress is uniform over the cross-section, i.e. T = C, what's the pressure gradient distribution and sketch it? L L. R
Use exact Equation fast.
Please show complete solution and clear explanation, thank you.
Solve it fast,,, hand written solution please.
G1/ In the fig.shown, the Flow rate Pipe (A) is equal ( QA = 25 Lit15), the diameter is equal ( DA = 75 mm, D, = De = Dc =30mm), and the velocity in Pipe (D) is equal (Uo=5 m/s), the relation between flow rate in in 6o mm, Pipe (B) and pipe (c) GB =3 Qc. Find the Value of '. Re, Qc, Qo. 2- UA, UB, Uc: Pe = 30 mm water Pc = 30mm imput QA = 25 2i+/sec OA= 75 mm = 6o mm input = A outPut = B, C, D accumulation = o.
3rd solution please
I need the answer as soon as possible
This is cryogenic subject question and i want ees code for the same as solution.
Please solve correctly, Show unit conversion (I don't know why there is conversion factor 1488 in the numerator)