Fluid Mechanics I Test. 2 Q:- Prove that the angle of inclination of two fixed parallel plate as shown in figure, so that laminar flow at constant pressure occurs is 12 μ Q 0 = sin-1 y a3 where:- Q:flow rate a:distance between plates Fig. fixed plates

Fluid Mechanics I Test. 2 Q:- Prove that the angle of inclination of two fixed parallel plate as shown in figure, so that laminar flow at constant pressure occurs is 12 μ Q 0 = sin-1 y a3 where:- Q:flow rate a:distance between plates Fig. fixed plates

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

P1 A thin layer of water flows down a plate inclined to the horizontal with an angle a = 15° in the shown coordinate system. If the thickness of the water layer is a=0.5 mm, assuming that the flow is laminar and incompressible, (water density p = 1000 kg/m³viscosity µ = 0.001 Pa.s and acceleration of gravity g = 9.81 m/s²) and an air flow shears the layer in a direction opposite to its flow with a shear stress of 1 N /m². Solve the Navier-Stokes equation: air water (a) to find the value of the maximum water velocity in m/s to three decimal points, Answer: (b)and to find the value of water velocity at the layer's surface in m/s to three decimal points, Answer:
(b) A Formula 1 team tests their car in a wind tunnel at a scale of 50%, at a speed of Vwinarunnet = 50 m/s. The measured downforce at this speed is Foownforce.WT = 3000 N and the model reference area is Aref wT = 0.5 m?. 1. Find the downforce magnitude on the full-scale race car at the same Reynolds number. Assume constant air density p = 1.2 kg/m. II. It is said that F1 cars could travel upside down, as shown below. At what speed should the full-scale car travel to achieve this, if its mass is m = 740 kg? The acceleration of gravity is g = 9.81 m/s?. Downforce Weight
6. Problem We want to know the velocity component of a fluid flow normal to a given surface: v, = v"n. Compute the normal velocity u, for the following normal vector and flow vector. ) --E- 3.0 v = m/s V3 1.0
Q1: The U tube (in Fig.1) is open at (D) and closed in (A). What will be the pressure at point (A, B and C): 1- Uniform acceleration (az=10m/sec?) to the top only. 2- Uniform acceleration (ax =10m/sec²) to the right and (az=10m/sec") to the top. 0.6m 0.9m Fig.1
1. A fluid is bounded by two parallel plates of infinite width and length as shown in FIGURE Q1. The upper plate moves at 7 m/s, and the lower plate is fixed. The fluid's dynamic viscosity is 1.85X105 N.s/m?. Assume Couette flow with pressure gradient, = 0.1 N/m³. a. Propose the discretization method to solve Couette flow equation with pressure gradient below. Let the number of nodes, n = 9, the distance between the nodes is 0.05 m. Obtain the velocity of all the internal nodes using the matrix inversion method and the iterative method. Compare the results and the effectiveness of both methods (in terms of calculation effort and ease of setting up the problem). + b. Flow shear stress is governed by the following equation ôu Propose the discretization method to solve the above equation and calculate the shear stress at node 1. Describe the condition in tems of the pressure gradient when the shear stress at the bottom plate is zero. Moving plate at Um/s N= N-1 `Fixed plate FIGURE Q1
g Figure 3: Fluid flows between two infinite plates A viscous, incompressible steady fluid flows between two infinite, vertical, parallel plates distance h apart, as shown in Figure 3. Use the given coordinates system and assume that the flow is laminar, fully developed (30), and planar (w = 0,0). Assume that pressure and gravity are not negligible. (a) Simplify the contnuity equation and show that v = 0. (b) Using the y-momentum equation show that pressure is a function of a only. (c) Find the velocity distribution u(y) in terms of u, g, h, p and d (d) Find the wall shear stress of the flow.
Question 3 (a) A two-dimensional flow velocity field in the domain with non-dimensional coordinates x > 0 and y > 0 is defined as: v = -Upxy i+ Upxy j where i and j are the unit vectors in the x- and y-directions respectively and Uo is a constant with units m/s. (i) Determine the magnitude and direction of the velocity at the point (1,1). (ii) Find the equation of the streamlines.
An airplane that has a cross-sectional diameter D = 4 m of the front portion is to fly at a speed of 600 km/hr in air that has a density of 1.1 kg/m and dynamic viscosity of 1.27 x 10 Pa.s. A small size model of scale ratio (1/17) to be tested in a different fluid that has a dynamic viscosity 5 x 105 Pa .s and a density of 500 kg/m2. It is determined that the parameters that are important for this test are: diameter D, density, viscosity, velocity V, the length of the wings L and the drag force F. What must be the speed (m/s) of the model to Choose... ensure dynamical similitude? What must be the corresponding diameter of the model (cm)? Choose.. What is the number/s of dimensionless groups for this problem? Choose...
An infinitely long cylindrical container has a cross section area of radius R, and is placed horizontally with gravity being in the −y direction, as shown in the figure. The cylinder is 50% filled with water (the shaded part), with density ρ. The other 50% of the volume in the cylinder is filled with air with constant pressure of p = p0. The length of the cylindrical container in the axial direction is W. c) Use control volume analysis and divergence theorem on the 4th quadrant water volume to compute the hydrostatic force acted on the 4th quadrant of the cylinder wall, as shown by the thickened line in the figure.
b) Derive the Navier-Stokes of continuity Equation If the fluid is incompressible, p = constant, independent of space and time, so that dp/ờt = 0. The continuity equation then reduces to v-v = 0.
1-15. Analyze the flow between two plates of Fig. 1-15 by assuming the fluid is a de Waele power-law fluid as in Eq. (1-31a). Compute (a) the velocity profile u(y) with the power n as a parameter and (b) the velocity at the midpoint h/2 for n = 0.5, 1.0, and 2.0. Answer: (b) u = V/2 for all cases 1-16. Reneat that
3) The viscosity of the Newtonian fluid with a density of 650 kg/m³ is determined with a viscometer as shown in the figure below. The required torque (T=F.r) applied to the inner cylinder (r¡ = 4 cm) to rotate with an angular velocity of 6 rad/s is 3x10-7 Nm. If the velocity distribution in the clearance between the cylinders is linear, a) Find the viscosity (µo) of the fluid b) Find the shear stress on the side surfaces in the viscometer if the viscosity varies according to µ= H0 (1-r/r2) where r2 = W=6rad/s 2cm 150mm ri+2 (cm) due to heating during rotation. .fluid