When crude oil (r.d = 0.855, µ = 71.8*104 Pa. s) flows in a 50 mm horizontal pipeline at 4.5 m/s, a pressure drops of 6500 kPa occurs in 60 m of pipe. Calculate the pressure drop in the corresponding length of a pipe model 25 mmd when gasoline (r.d = 0.68, µ = 2.9*104 Pa. s) flows in the model for complete similarity between model and prototype. %3D

When crude oil (r.d = 0.855, µ = 71.8104 Pa. s) flows in a 50 mm horizontal pipeline at 4.5 m/s, a pressure drops of 6500 kPa occurs in 60 m of pipe. Calculate the pressure drop in the corresponding length of a pipe model 25 mmd when gasoline (r.d = 0.68, µ = 2.9104 Pa. s) flows in the model for complete similarity between model and prototype. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.4 A 200 mm diameter pipeline is laid on the ground. At a particular point, the piezometric head is 20 m. Total energy head of water at a point is 26 m. The Discharge (L/s) of water through the pipe is Type your answer here.. SUBMIT
The figure shown below is a series pipeline system used to draw a fluid from a lower source open tank to a higher destination open tank . The flow and geometric layout for the system are listed below: Fluid: water Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m of two free surfaces Suction line: DN100 Sch. 40 Steel pipe Length: Ls=2.0 m Valve1: hinged disc type foot valve Entrance type: well-rounded Discharge line: DN80 Sch. 40 Steel pipe Length: Ld=100 m Valve2: full open gate valve Elbows: 90ο long radius elbow (1) Select the simplified general energy equations for section 1 and 2_________ A. B. C. D.
Solve it..
Z\0 @ P 0:10 ZAIN IQ II. Quiz 2 Thermo.pdf Gas flowing through a diverging nozzle has at inlet section a temperature of 20 °C, pressure 120 kN/m² and velocity 300 m/s. At the outlet of the nozzle the velocity has fallen to 100 m/s. Assuming an adiabatic flow, what is the values of outlet pressure, temperature, internal energy and specific enthalpy at outlet section. Take y= 1.333 and Cv= 0.86 kJ/kg K.
Describe the methodology for obtaining the pump curve in a project, where data are collected at five points with different pressures in the pump (10 psi, 15 psi, 20 psi, 25 psi and 30 psi), where to find these flow rates Q a 1000 ml bottle is used and the time required to fill it is timed, for each of the pump's five pressure points. The gauge pressure H in meters of water column reached must also be observed in order to construct the HxQ graph of the pump. This entire process is carried out for three different types of piping systems, each with its characteristic pressure drops.
I need the answer as soon as possible
The length of a tube carrying fluid is increased by 1.75 times its original value. All other parameters remain unchanged. What is the new flow rate through the tube if the original flow rate before the increase in length was 4.50. L/min? (Usc Poiseuille's Law), : 2P 87) L
A) A 0.4 m diameter fan running at 970 rev min' is tested when the air temperature is 10 °C and the barometric pressure is 772 mm Hg and the volume flow rate Q=0.7 m s. Find the corresponding volume flow of a geometrically similar fan of 1 m diameter, running at 500 rev min at same conditions. Assume that the fan efficiency is unchanged. Ja
Fluid
I need the answer as soon as possible
Engine oil at 40 C [density 876 kg/m^3, viscosity 0.2177 kg/m.s] flows in a 21-cm-diameter pipe at a velocity of 1.1 m/s. The pressure drop (in Pa) of oil for a pipe length of 24 m is ?"
Real System Fluid: Hydrogen Gas at 1 atm T. = 200 K U, = 20 m/s L = 0. 30m Model System W h = 40 U Fluid: Air at 1 atm m² K T. = 300 K U = ? L = 0.50 m h = ?