Two wrenches are used to tighten the pipe. The pipe ismade from a material having an allowable shear stress ofTallow = 80MPa. The pipe has an outer diameter of 25mm and inner diameter of 20 mmFigure 1Pof 1250 mmB<250 mm>PDetermine the allowable maximum force P that can be applied to each wrench.(Figure 1)Express your answer with the appropriate units.μAP = ValueSubmitUnitsMy Answers Give Up?Provide Feedback

Answered: Two wrenches are used to tighten the…

Two wrenches are used to tighten the pipe. The pipe is made from a material having an allowable shear stress of Tallow = 80MPa. The pipe has an outer diameter of 25 mm and inner diameter of 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa, Ebr 100 GPa. Figure P P -10 mm -20 mm 1 of 1 Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the steel. Express your answer to three significant figures and include appropriate units. Ost = Submit Part B Obr = Submit 0 Value If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the bronze. Express your answer to three significant figures and include appropriate units. Provide Feedback A Request Answer Value Units Request Answer Units ?
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L1 = 55 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.35 in., a wall thickness of 0.07 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.3 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
4. A titanium alloy (Ti-6Al-4V) pipe has a bronze C86100 copper alloy core and is subjected to a force, P = 150 kN. Determine the average normal stress in each material and the elongation if the pipe has an outer diameter of 90 mm and an inner diameter of 70 mm. (Solution: On = 25.789 MPa, 22.135 MPa, 8 = 0.086 mm) 400 mm-
A tie-down on the deck of a sailboat consists of a bent bar bolted at both ends, as shown in the figure. The diameter d_B of the bar is 1/4 in., the diameter d_W of the washers is 7/8 in., and the thickness t of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P_allow on the tie-down?
Two aluminum plates, each having a width b = 7.5” and thickness t = 2”, are welded together as shown in the figure. Assume that a = 5.0”. Specifications require that the normal and shear stress magnitudes acting in the weld material may not exceed 40 ksi and 25 ksi, respectively.
Ch 1. Answer with complete solution. Thankyou.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.0 ksi. Brass segment (2) has an outside diameter of 0.75 in., a wall thickness of 0.13 in., a length of L₂ = 28 in., a shear modulus of 6400 ksi, and an allowable shear stress of 7.7 ksi. Determine: (a) the allowable torque TB that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. y L₁ L2 TB. X (1) (2) N Answer: (a) TB = (b) T₁ = T₂= (c) DB = lb-ft lb-ft lb-ft rad B C
PLEASE ANSWER ASAP TY! a) Determine the cross-sectional area of the structural tube (in mm2) b) Determine moment of inertia of the cross-section about the neutral axis (in mm4) c) What is the maximum normal stress at point K (in MPa)? Include negative sign if compressive. d) What is the axial stress at section H-K (in MPa)? Include negative sign if compressive. e) What is the flexural stress at section H-K (in MPa)? f) What is the maximum normal stress at point H (in MPa)? Include negative sign if compressive.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (ay) MPa, and for the bronze (ay)or 520 MPa, determine the magnitude of the largest elastic load P 640 that can be applied to the assembly. E 200 GPa, Ebr= 100 GPa. 10 mm 20 mm Figure 2: Steel Bolt
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. Thesteel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assume a = 4.1 m, b = 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? (1) P (3) B (2) Answer: P = 117.7 kN
SOLVE COMPLETELY. SHOW COMPLETE SOLUTION, INCLUDE FBD
A gusset plate is connected to the flange of column with the help of fillet weld on both sides as shown in the figure. The direct shear stress and bending tensile stress are 70 MPa and 130 MPa respectively. Find the equivalent stress (in GPa). Gusset plate I-section flange