QUESTION 3 The assembly consists of three steel rods and a horizontal bar BED. The structure supports a 36 kN load Plocated at middle of bar BED. Each of the rod AB and CD has a cross-sectional area of 200 mm2 and rod EF has a 625 mm². Modulus of elasticity for steel is 200 GPa. Determine: (a) The change in length of rod EF. (b) The stress in each rod. 500 mm 400 mm

QUESTION 3 The assembly consists of three steel rods and a horizontal bar BED. The structure supports a 36 kN load Plocated at middle of bar BED. Each of the rod AB and CD has a cross-sectional area of 200 mm2 and rod EF has a 625 mm². Modulus of elasticity for steel is 200 GPa. Determine: (a) The change in length of rod EF. (b) The stress in each rod. 500 mm 400 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m 10KN 0.8m 0.4m 5KN 0.6m What is the deformation 8Rc in mm? Al 20KN A=800 mm? A=1,200 mm²
Someone can help me with these. I'm stock, please.
dont round off if not yet the final answer pls
Topic: COMBINED STRESS - STEEL DESIGN Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 60 GPa] with a cross-sectional area of A1 = 870 mm?. Bar (2) is a bronze alloy [E = 92 GPa] with a cross-sectional area of Ay = 520 mm?. Assume L$=2.6 m, La=2.9 m, a=0.7 m, b= 1.3 m, and c= 1.1 m. All bars are unstressed before the load P is applied; however, there is a 3.9-mm clearance in the pin connection at A. If a load of P= 58 kN is applied at B, determine: (a) the normal stresses 01, 02, in both bars (1) and (2). (b) the normal strains € , E2, in bars (1) and (2). (c) determine the downward deflection vA of point A on the rigid bar.
Round off final ans, dont round off initial values
Portions of a x-in. square bar have been bent to form the two machine components shown. Knowing that the allowable stress is 18 ksi, determine the maximum load that can be applied to each component. (a) 1 in. (b) The maximum load that can be applied to component (a) is The maximum load that can be applied to component (b) is lb. lb.
NOTE: Refer to MM = 08 and DD = 20
The aluminum bar ACDB is rigidly connected to a steel tube in CD. The data is presented in the table. If the load P is equal to 125 kN, determine: The stress of aluminum in segment AC. Answ: 63.66 MPa The stress of aluminum in segment CD. Answ: 13.93 MPa The stress in steel in segment CD. Answ: 39.79 MPa The total deformation of the bar. Answ: 0.29273 mm
SHOW COMPLETE SOLUTION AND ILLUSTRATION
When designing a structural member, which of the following statements is FALSE? Select one: A. The allowable stress is used in calculating the maximum load to be applied. B. The ultimate stress depends on the Factor of Safety used. C. The ultimate stress is determined based on the material used. D. The allowable stress depends on how conservative the design is.
The shaft is made of A992 steel. It has a diameter of 0.7 in. and is supported by bearings at A and D, which allow free rotation. The shear modulus of elasticity for the material is 11 × 10³ ksi. 2 ft < 5 of 7 Part A B 2.5 ft > 60 lb-ft C 3 ft O 60 lb-ft