Two possible OHV combustion chambers are being considered. The first has two valves, and the second has four valves per cylinder. the diameter of the inlet valve is 25mm for the first valve design and 15.5 mm for the second. If the second design is adopted , calculate the percentage that the total valve perimeter is increased by. If the valve lift is the same between the two designs, calculate the percentage increase in curtain flow area

Two possible OHV combustion chambers are being considered. The first has two valves, and the second has four valves per cylinder. the diameter of the inlet valve is 25mm for the first valve design and 15.5 mm for the second. If the second design is adopted , calculate the percentage that the total valve perimeter is increased by. If the valve lift is the same between the two designs, calculate the percentage increase in curtain flow area

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pipeline with a pump carrying a 50 L/s discharge leads to a nozzle as shown. If the 180 mm diameter pipe is made of cast iron while the 120 mm diameter pipe is made of commercial steel. Determine the head of the pump using the energy equation from pt. A to pt. C. The fluid is water with a kinematic viscosity of 1.02 x 10-6 m³/s. El. 20 m Water B 180-mm dia. pipe 200-m long pipe 300-m long pipe 120-mm dia. pipe El. 10 m El. 30 m
A cylinder having a diameter of 6 in (152mm) and a stroke length of 25 in (635mm). The exit time will be 5 seconds. The system operates with a pressure of 50 psig (3.45 bar) and there will be a pressure loss of 2 psi. What will be the Cv of the valve to be installed? [Answer: 1.99]
A 7.5 cm diameter orifice (Cv= 0.95, Cc= 0.65) is under ahead of oil (s=0.72). Determine the pressure of the air on the oil surface so that the available power in the issuing jet of oil is 6kW. Include a diagram in your solution. a.86 kPa b.76 kPa c.56 kPa d.66 kPa
Oil of SG 0.75 flows through the nozzle shown and deflects the mercury in the U-tube gage. What is the pressure at B in Kpa? A 2.75 D h B C Hg(13.6)
Not sure how to do this one. Would appreciate a full solution, thanks!
4. Calculate the volume flow rate of oil from the nozzle and the pressure at point B and D.
A 1.5-ft³rigid tank contains saturated refrigerant-134 at 170 psia. Initially, 20 percent of the volume is occupied by liquid and the rest by vapor. A valve at the top of the tank is now opened, and vapor is allowed to escape slowly from the tank. Heat is transferred to the refrigerant such that the pressure inside the tank remains constant. The valve is closed when the last drop of liquid in the tank is vaporized. Determine the total heat transfer for this process. R-134a, Sat. mixture P = 170 psia V = 1.5 ft³
Friction loss in pumping oil to pressurized tank an oil having a density of 833 kg/m3 and a viscosity of 3.3 x 10³ Ns/m² is pumped form an open tank to a pressurized tank held at 345 kPa (gage). The oil is pumped from an inlet at the side of the open tank through a line of commercial steel pipe 3-inch nominal pipe size r of internal diameter 77.92 mm at the rate of 3.494 x 10³ m³/s. The length of straight pipe is 122m and the pipe contains two elbows (90") and a globe valve half open. The level of the liquid in the open tank is 20 m above the liquid level in the pressurized tank. The pump efficiency is 65%. Calculate the kW power of the pump (1.40 HP) elbow Globe valve 20 m PUMP
Air with a mass flow rate of 5 kg/s enters a horizontal nozzle operating at steady state at 450 K, 350 kPa, and velocity of 3 m/s. The nozzle is well insulated. At the exit, pressure is 300 kPa and temperature is 390 K. Using the ideal gas model for air, the area at the inlet is m², and the velocity at the outlet is Are potential effects negligible? Why? m/s. Is heat transfer negligible? Why? Note that you may choose to model the specific heat as constant.
2. The jet passes through a point A, as shown. Calculate the flow rate. Assume the flow is frictionless and incompressible. 75 mm d 150 mm d- 30- -- 30 m 15 m
An absorption column is to be designed to recover 99.5% of the NH3 from a feed stream, which is supplied at 72 oF and an NH3 partial pressure of 10 mm Hg.
Crude oil (with specific weight γoil = 55 lb/ft3 ) is pumped at a rate of 400 gallons per minute from a test separator at A to the stock tank shown using a pipe that has a diameter of 4 inches. The pressure at A (to the left of the pump or prior to the pump) is 4 psi and the stock tank is open to the atmosphere. The friction head loss along the entire length of the pipe from A to B is 45 inches. Note that 1ft3 = 7.48 gallons. (a) Determine the velocity in the pipe. (b) Determine the head gain, ℎ??, delivered by the pump to the flow. (c) Determine the power required to run the pump if it is 90% efficient.