Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15.3 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 87.95 MPa and its angle of twist is limited to 5.41°. Use G = 80.32 GPa for steel and L= 433 mm. Round off the final answer to two decimal places. ... P -300 mm P- B L A

Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15.3 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 87.95 MPa and its angle of twist is limited to 5.41°. Use G = 80.32 GPa for steel and L= 433 mm. Round off the final answer to two decimal places. ... P -300 mm P- B L A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.0 ksi. Brass segment (2) has an outside diameter of 0.75 in., a wall thickness of 0.13 in., a length of L₂ = 28 in., a shear modulus of 6400 ksi, and an allowable shear stress of 7.7 ksi. Determine: (a) the allowable torque TB that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. y L₁ L2 TB. X (1) (2) N Answer: (a) TB = (b) T₁ = T₂= (c) DB = lb-ft lb-ft lb-ft rad B C
Answer the problem question, use 2 decimal places as final answer ( Examples of 2 decimal: 62.067 write as 62.07 ) Then box the final answer. Don’t forget the unit. Write it on paper, showing the correct answer and solution.
In the figure shown, assume that a 21.3-mm-diameter rivet joins the plates that are each 118 mm wide. The allowable stresses are 119 MPafor bearing in the plate material and 54 MPa for shearing of the rivet. Determine the minimum thickness of each plate. (Answer must be in millimeters) Round your answer to 2 decimal places.
A so-called "trapeze bar" in a hospital room provides a means for patients to exercise while in bed (see figure). The bar is 2.3 m long and has a cross section in the shape of a regular octagon. The design load is 1.4 kN applied at the midpoint of the bar, and the allowable bending stress is 180 MPa. Determine the minimum height h of the bar. Round to one decimal place. (Assume that the ends of the bar are simply supported and that the weight of the bar is negligible.) hmin mm
1. For the riveted connection shown in the figure using elastic analysisa. Determine the safe value of P if the allowable shearing stress of 25mm rivets is 150MPab. Determine the maximum shearing stress that can be develop in the rivet for a given load ? = 52??c. Determine the minimum shearing stress that can be develop in the rivet for a given load ? = 52?N
please answer asap
hand written asap (solve all parts)
Urgent please solve quickly. a = 10 , b = 7 solve this question about this information. Extra information: Take both loads 35 kN
2 please with explanation :)
Please provide detailed solution, 100%guarantee to vote it up. Thank you. ( a ) r = ? m ( b ) r = ? m
A flanged bolt coupling consists of six - ½ inch steel bolts evenly spaced around a bolt circle of 12 inch in diameter, and four – ¾ inch aluminum bolts on a concentric bolt circle 8 inches in diameter. With an applied torque of 260 kips*inch. determine the max shearing stress in the aluminum and steel bolt. Use Gst = 12x10 6 psi and Gal = 4x106 psi
please recheck your final answer.