To test the deflection on a uniform 100-kg beam, a boy of who weighs 50 kg exerts a pull of 150N on the rope rigged as shown. -1.5 m 0.75 m 0.75- -2.5 m Determine the components of the Weight Vector (W), used to represent the weight of the beam. W - Wxi + WJ (Answer in Newtons) W, Choose. W, Choose.

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: Convert to isometric drawing mark point A as the lowest point

A: use a 30-60 triangle to create the isometric  figure ng follow the left, front and top illustration…

Q: Tabulate the absolute coordinates. Write a program to drill the holes and mill the rectangular…

A: Given: To find: Write a program to drill holes and mill

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Consider a virtual load Q, acting vertically downwards, is applied at point A.Draw the given truss…

Q: how to you get the Q1 = 70.3

A: In this problem, it is asking how did we get Q1=70.3 kJ/kg.

Q: A garden hose attached with a nozzle is used to fill a 20 Liters bucket. The inner diameter of the…

A: Given Data  V=20 L=0.02 m3 t=50 sec dnozzle=2.45 cm=0.0245 m

Q: Q- In a limit System, the following limits are Specified for hole and shaft. calculate the tolerance…

A: The limits of the hole are..The limits of the shaft are..

Q: What is the SAE horsepower of an 8-cylinder engine with a bore of 4.556 inches? Round to the nearest…

A: Given data:- no of cylinder (n)=8 bore (d) =4.556 inches To find:-the SAE horsepower

Q: 2. From the given figure below, solve for the bar Y from the reference line. (choose the nearest…

A:

Q: The given figure shows a casted I shape made from steel. You are required to design a wooden pattern…

A: According to the details provided in the question, we need to create a pattern with steel. First, we…

Q: Draw back the drawing given  with the scale 1:1 on the new drawing paper using all the method on…

A: 1. First off all we need to locate the two points of the given part at distance of 200 mm apart in…

Q: Round off the numbers in the following problems to three significant figures. Find the percent…

A:

Q: Show your steps and label units on all answers. 1.) Determine the Forces in all the members, and the…

A:

Q: Determine ly and ky.

A:

Q: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

A:

Q: ect with dimension. mode 50 R20 Ø20 25 15 Ø32 Ø60 80 45 50 60

A: According to the details provided in the question, we need to DRAW the half sectional view of the…

Q: Please use different values. This answer you already gave me for a similar question. These values I…

A:

Q: Round number to three significant figures. 1.548937 x 10^7

A: For scientific notations significant digits/figures are calculated only for the coefficient or…

Q: A midsized Dozer weighs 41,000 pounds and has 175 hp. If the machine is working at 80% efficiency…

A: Given Data The weight of the machine is: W=41000 lb The power is: P=175 hp The efficiency of the…

Q: On the toleranced rectangle below, state the tolerance within which the top surface must be flat. O…

A:

Q: +0.15 +0.25 The dimensions for the shaft size are Ø30 –0.25 mm and the hole size are Ø30 - 0.15 mm.…

A: Solution:

Q: What is the weight of 3 slug, expressed in pounds-force? o 96.522 lbf

A: Given      Weight = 3 slug

Q: Determine the magnitude of F so that the resultant couple moment is 11.5 kN -m , counterclockwise.…

A:

Q: Compute the thickness of the web, t, of the channel shape section

A:

Q: A plate was subjected to a tensile force P=100 KN as shown on the figure. If the allowable stress is…

A:

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your…

A: Given : To find : Volume of the body

Q: Round number to three significant figures. 0.000045389

A: Given data: The given number is N = 0.000045389. Here, there are a total of 5 significant figures.…

Q: 8 inch radius 8 inch circumference 8 inch all around 8 inch diameter R.70 4x 1.40 B IP 1.00 SECTION…

A: Select the correct statement about the notation circled in green and marked as letter.C. Assume all…

Q: Calculate to the correct number of significant figures. 9.15/4.970

A: Given Data: The given number N1 = 9.15 The given number N2 = 4.970 The number of significant…

Q: a. Determine the magnitue of P and F (in N) if the resultant of the five force shown is 1000N…

A: The given system of force is as shown below, The given forces are as follows. F1=840…

Q: The water (density =1000 kg/m3) leaves the nozzle (area of the nozzle=0.01 m). Assuming steady,…

A: GIVEN :- height of stagnation tube : h= 50 cm area of nozzle : A= 0.01 m2 S.G = 10.4  ρ=10400 kg/m3…

Q: Round off the following number to three significant figures:68.534s

A: The given no. is 68.534 s The given no. is having 5 significan figures as the number of digits are…

Q: What power can be delivered by the turbine if its efficiency is 100%? The water flow rate is 0.01…

A: Given:η=100%Q=0.01 m3hL=13.8H=20 mρ=1000 Kg/m3

Q: Draw Front and Side and top with all dimensions please

A: Draw the top view and side view first as shown in the below attached image:

Q: Round off the numbers in the following problems to three significant figures. Find the percent…

A: Original Number = 6748.3 After Round off up to three significant number = 6750

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.