Draw Front and Side and top with all dimensions please

Q: termine the discharg

A: for the other end to open to the atmosphere the net headloss in the pipe should be equal to 3m this…

Q: Find the acceleration in terms of F. 回 m₁

A:

Q: Two farmers are pushing on a gate with forces FA and FB, applied at locations A and B respectively.…

A: Given : To find : Equations of static equilibrium

Q: 30r 20dls 20 10r 20 20 30 150 100

A:

Q: Knowing that P =75 N and Q=195 N, determine graphically the magnitude and direction of their…

A:

Q: Two plates are connected by a bolt as shown in the figure. What is the shear stress on the bolt?

A: Given Data

Q: L P The axially loaded member is pin-connected at one end and fixed at the other. The member has a…

A: There is pin connected at one end and fixed support at other end.The cross sectioin is square of…

Q: 5/4 Specify the x-, y-, and z-coordinates of the mass center of the quarter-cylindrical shell. 360…

A:

Q: 2. A flat annular steel disk of outer diameter 0.6 m and inner diameter 0.3 m, p = 7800 kN*s/m“, v =…

A:

Q: 5. An ideal Otto engine, operating on an air standard with k=1.35 has a compression ratio of 5. At…

A:

Q: 2. Shown below is the binary lead-tin phase diagram from your textbook. Answer the questions below.…

A: a. Proeutectic composition is calculated at the temperature just above eutectic line of 183°C As the…

Q: 2. (03) The splined ends and gears attached to the A992 steel shaft are subjected to the torques…

A: Note:- here, part C). and D). has been asked so, I have answered that two parts here.here for steel…

Q: 1. A solid aluminum alloy disk with uniform thickness has an allowable speed of wall = 40,000 RPM, a…

A:

Q: Draw the front,top and R.H.S/L.H.S view of the given figure attached below.write the processes too…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Problem 3: When x = 10 ft, the crate has a speed of 20 ft/s which is increasing at 6 ft/s².…

A: At x = 10 ft, the position of the center of the crate to the vertical axis is given by y =…

Q: R20 R28 XL 296

A: Given: Draw the front, Side and top

Q: This is the ISO1940 balancing grades. Explain the chart and how can we use it? Where do we use?…

A: ISO 1940 are quality characteristics, or the chart given is used to compare rotors of different…

Q: 21 15 99 TOLL 20

A: To draw: The Front view, Top view and Side view.

Q: Draw the isometric drawing

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: You are expected to design a simulation environment for a bicycle with a kinematic model. The…

A:

Q: •5-53. The 20-mm-diameter A-36 steel shaft is subjected to the torques shown. Determine the angle of…

A: Given            Diameter, d = 20 mm For A 36 steel  Shear modulus, G = 75 GPa Find   Angle of twist…

Q: The jet aircraft has a total mass of 21 Mg and a center of mass at G. Initially at take-off the…

A: Given data with variables. m=21 Mg=21×103 kg2T=6 kNT'=2.1 kN   It is required to determine the…

Q: Prob. 9–16 •9-17. Determine the equivalent state of stress on an element at the same point which…

A:

Q: Name. Find the stresses on the 20 degree plane shown. Dřaw and label the Mohr's circle. Fill in the…

A: given; stress in x direction(σx)=-10MPa (compressive)stress in y direction(σy)=8MPa (tensile)shear…

Q: A circular plate of diameter (1.36 m) is placed some how 1.5 meter above the room floor, if the…

A: Solution:

Q: 1. 100 mm The bar has a diameter of 60 mm. If it is subjected to the force components as shown in…

A:

Q: Create an orthographic projection of the following object. Draw the three standard 4X 50X 50 views.…

A: Orthographic projection is a represention of three-dimensional structure in two dimensions.

Q: Draw Front and Side and top with all dimensions please

A: According to the question,A  3-D object is provide, we need to draw three projection views of the…

Q: A simply supported beam of circular cross section of 0.15 m diameter with a span of 1m is subjected…

A:

Q: Two farmers are pushing on a gate with forces FA and FB, applied at locations A and Brespectively.…

A: Force Fb

Q: ASME Y14.5-2009. PART TO BE FREE OF BURRS AND SHARP EDGES. D.001 VACUUM, BAKE (10-4 TO 105 TORR).…

A: If will attached part by part look like heat tube exchanger

Q: Water (5.0 L/min) is flowing in a tube “D = 3 cm, L= 5 m" and is to be heated from 15°C to 60.3°C by…

A:

Q: Water is flowing in a tube "D = 3 cm, L= 5 m" and is to be heated from 15°C to 47°C by applying a…

A:

Q: When an inductor and a resistor are connected in parallel, how many degrees out of phase are the…

A: According to Bartleby guidelines, we can solve only three sub part of a question at a time. you are…

Q: Two horizontal

A: In general, there are three modes by which heat gets transferred from one place to another. The…

Q: 2. The a-t curve for a particle having rectilinear motion is shown in the figure. At t=e, the…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.