Please help I will give you good ratings Modify the part created in Problem 3A as indicated in the multiview drawing below.Enter the numerical value of the surface area of the part in square inches. Your answer should include two decimal places.2X R.60RI652X 0.600101001.00S.00

Given Orthographic view of the part To find Surface area of the part

Answered: Please help I will give you good…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5
Q6 Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke length of 400 mm. What is the engine capacity in litres? Give your answer to 2 decimal places.
Choose the correct answer below and show your solution completely. Make sure that your finals answer is 4 decimal places.
Select the correct statement about the notation circled in green and marked as letter C. Assume all dimensions are in inches. 4x375 A с 8.00 Lo A- Hoy 4x5.25 4x 4.75 4x R.70 4x 115.0 4x 1.40 B 4x 2.00 4x 1.20 6.00 25 M₂ 4x.75 4x 25 .75 1.00 Ø6.50 SECTION A-A SCALE 0.400 4
2. For the plan area shown, determine the location of the Centriod. Use you're the last two digits of your ID for the missing length x mm. ID:88 The following table facilitates the calculations for the required data 5 mm 10 mm 3 mm 10 mm x mm
Select the correct statement about the notation circled in green and marked as letter B. Assume all dimensions are in inches. 4x375 A с 8.00 HOH 4x5.25 4x 4.75 4x R.70 4x 115.0 4x 1.40 B HOH 4x 2.00 - 4x 1.20 6.00 25 11 4x.75 4x.25 .75 1.00 6.50 SECTION A-A O SCALE 0.400
READ THE INSTRUCTIONS: Do not round off intermediate values when using them to solve subsequent calues; however they may be written up to 4 decimal places. final answer should be rounded off up to 4 decimal places. I'll upvote if it is correct and compelete. Thank you
Round off the numbers in the following problems to three significant figures. Find the percent difference between each rounded-off number and the original number by using the original number as the reference. 6748.3
Show the tolerance zone for the given slot. Superimpose the tolerance zone on the given drawing. Dimension the width of the tolerance zone and the offset from the true profile.
52 What is the distance between the center of circle A and the corner at B? R3 03 Start a new drawing based on Mech-Millimeters.dwt. Draw the object shown in Figure A-1, starting with the center of the Ø3 circle at point 5,5. Draw only the object, not the dimensions and then answer the following questions: O 186794 198628 193132 171870 R1.0 TYP. 18 8 2 2 1 10
An irregular shaped metal sheet is to be constructed with a measurement of 10m x 15m x 20m x 25m. Do the necessary CALCULATIONS in order to design in the inches the metal sheet on a drawing sheet if the design scale is 1:200. SHOW how it will be formed on a drawing sheet.
How would you solve this?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS