To produce more power the upper management decided to modify the power plant by placing the stage 2 as a saturated liquid stage. The condenser site was planned to leave as it is with the same parameters. The flow rates stays the same. See the figure below for the data. Again, this an ideal case: S2-S1; S3=S4. Boiler P1=36.29bar Lin Turbine Condenser P2=2.26 bar -2 Saturated vapor T6=? 6 Cour ||T5=15C 5 Cooling water Pump 3 saturated liquid

To produce more power the upper management decided to modify the power plant by placing the stage 2 as a saturated liquid stage. The condenser site was planned to leave as it is with the same parameters. The flow rates stays the same. See the figure below for the data. Again, this an ideal case: S2-S1; S3=S4. Boiler P1=36.29bar Lin Turbine Condenser P2=2.26 bar -2 Saturated vapor T6=? 6 Cour ||T5=15C 5 Cooling water Pump 3 saturated liquid

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter3: Refrigeration And Refrigerants

Section: Chapter Questions

Problem 12RQ: The condensing pressure is 260 psig and the condenser outlet temperature is 108F for R-22. By how...

See similar textbooks

Similar questions

When a standard-efficiency air-cooled condenser is used, the condensing refrigerant will normally be higher in temperature than the entering air temperature.
If the evaporating pressure was 76 psig for R-22 and the compressor inlet temperature was 65F, what would be the total superheat entering the compressor? A. 11F B. 21F C. 10F D. 20F
To produce more power the upper management decided to modify the power plant by placing the stage 2 as a saturated liquid stage. The condenser site was planned to leave as it is with the same parameters. The flow rates stays the same. See the figure below for the data. Again, this an ideal case: S2-S1; S3=S4. Boiler P1=36.29bar Lin Turbine Condenser P2=2.26 bar -2 Saturated vapor T6=? 6 Cour ||T5=15C 5 Cooling water Pump 3 saturated liquid
please explain how to obtain those values, how you get alll the values in the imagine.
solve using image, please don not resend other solutions previosly posted in bartebly ,as the are wrong thanks
Please explain steps
Find the following: a. Enthalpy of the steam in kJ/kg entering the condenser b. Enthalpy in kJ/kg of the condensate c. Enthalpy in kJ/kg of the feed water
A single compressor using ammonia as refrigerant has three evaporators of capacity 30 TR, 20 TR and 10 TR. The temperature in the three evaporators is to be maintained at -10°C, 5°C and 10°C, respectively. The system is provided with individual expansion valve and back pressure valves. The condenser temperature is 40°C. Assume isentropic compression: a. Draw the P-h diagram. b. What is the mass of refrigerant flowing through each evaporator? c. What is the power required to drive the compressor? d. What is the COP of the system?
Problem 2: Win High-pressure liquid water (Pump Boiler Condenser à out Low-pressure liquid water FIGURE 7-1 Example of a power cycle. High-pressure steam 3 Turbine Wout Low-pressure superheated vapor or high-quality two-phase mixture A simple steam power cycle consists of a boiler, turbine, condenser, and pump as shown in the sketch above. All the heat removal in the cycle is done by the condenser which transfers the heat to pipes carrying cooling water. The cooling water has a mass flow rate of 7 kg/sec, and a specific heat of 4,180 J/kg-°C. The cooling water is supplied at a temperature of 10 °C and exits at 20 °C. Heat is supplied to the cycle through a steam boiler at a rate, Ċin = 420 kW. Find the following: a. The rate at which heat is rejected from the cycle to the cooling water, Qout- b. The net power produced in kilowatts, Wnet- c. The cycle efficiency, cycle.
A direct contact condenser of the spry type receives 60 kg/s of 925 quality steam at 0.06bar. A dry cooling tower system cools the feedwater to 15 oC. calculate the condensatepump volume flow rate , and the pump power input if the pressure losses in the dry coolingtower system are 2 bar and the pump efficiency is 0.7.
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 + (200/13) kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: PV and TS diagrams of the cycle showing ideal and actual process lines Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.____________________________ Rankine engine efficiency (%). Ans.____________________________ Cycle thermal efficiency ( %). Ans.____________________________
A reheat cycle with two stages of reheating is executed with steam expanding initially from 20 MPa and 540C. The two reheater pressures are 3.8 MPa and 0.97 MPa, and the steam leaves each reheater at 540C. Condensation occurs at 60C. Compute the efficiency of the cycle. (Attach your T-S and schematic diagram of this problem)