To determine the strength of the riveted joints in a cylindrical vessel, tensile tests were performed on the 6-in.-wide specimens, as shown in the figure. The tensile force P at failure was found to be 32 lcips for the longitudinal joint specimen and 16 kips for the circiunferential joint specimen. Determine the largest allowable inner diameter of the cylinder that can supp

Q: A uniaxial test was performed on a bone specimen having a central (gauge) region initially 6 mm long…

A: a uniaxial test results were given as followslength=6mmdia=2mm

Q: A punch of 20 mm diameter is used to punch a hole in 8 mm thick plate. If the force required to…

A: Here, We need to calculate the average shear stress on the plate. diameter = 20 mm thickness = 8 mm…

Q: The following observations were made during a tensile test on a mild steel specimen 40 mm in…

A: Given data : Tensile load P=40 KN Change in length ∆L=0.0202 mm Initial length L=200 mm Diameter of…

Q: Test No Temperature C Deformation rate(mm/min) Strain at break Youngs modulus (Gpa) Stress at…

A: Step 1: UTS mean Ultimate tensile strength. From the conventional stress strain curve, it is…

Q: A UTS with a machine stiffness of 75 KN/mm is used to measure oad/displacement points in the elastic…

A: Given dataDeflection (ΔL) = 0.1 mmInitial length (L) = 102 mmLoad (F) = 2000 NMachine stiffness (k)…

Q: Q1) A specimen with the given dimension is loaded as given in the figure below. Determine; a) The…

A: As per the guidelines of Bartleby we are supposed to only answer the first three subparts of the…

Q: 5. A tensile test was done on a magnesium sample of original diameter and original length of 12mm…

A: To plot the stress v/s strain curve and to find the required parameters   Note: as per the answering…

Q: O AF F. p0.2 p0.2 p0.2 S. 0.2-mm (0.2% of 100 mm=0.2-mm)- AL II R.

A:

Q: A circular specimen with a diameter of 1.65 and a length of 11.96 was subjected to a force equal to…

A:

Q: 30 20kN PVC Wood 20kN 50mm

A:

Q: A specimen is originally 300mm long and has a diemter of 11mm and it subjected to a force of 4kN.…

A:

Q: A steej two fixed points. The tensile force in the rod at 70°F is 1200lb. If a = 6.5x10-6/°F and E =…

A:

Q: Can you please answer the following question in the picture and show all of your work in, please.

A: Detailed step by step solution is given below, still if you have any query please feel free to…

Q: Arod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 18…

A: D=18mm L=160mm

Q: A 0.375 -in. thick rectangular alloy bar is subjected to a tensile load P by pins at A and B. The…

A: Given data in question  Load 11 kips Thick 0.375 inch Height 3 inch Strain in longitudinal and…

Q: Briefly describe a standard test method which can be used to establish properties of Yield stress…

A: Tensile testing gives a wide range of information about a material.

Q: A circular tube of outer diameter D is slipped over a 40-mm-diameter solid cylinder. The tube and…

A:

Q: Q- 7 b, A bar specimen of 36 mm diameter is subjected to a pull of 90 kN during a tension test. The…

A: Given data- A bar specimen- Diameter d=36 mm, Change in diameter ∆d=0.0046 mm, Gauge length L=200…

Q: snip

A:

Q: Problem NO. 2. A student performed a tensile test in one of his samples, an aluminum specimen which…

A:

Q: A hollow cylinder with an OD of 100mm and an ID of 30mm, supports a load of 100kN. What is the…

A:

Q: A sample material with circular cross-section tapers uniformly. Over a gauge length of 200mm, it…

A:

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: 1.5-7 The data shown in the table were obtained from a tensile test of a metal specimen with a…

A:

Q: 1. A vertical pressure of 70 MPa is applied to an aluminum cube sample with a length of 10 cm on…

A:

Q: 7. Three rods of different materials are connected as shown in the figure. (a) Determine the maximum…

A:

Q: Q.12. In a tensile test a test piece of 25 mm diameter, 200 mm gauge length, stretched 0.0975 mm…

A:

Q: amplitude was 210 MPa. Compute the maximum and minimum stress. (Enter your answers to three…

A:

Q: Calculate the tensile stress when applied force of 1200ON on specimen of diameter of 7mm

A: tensile stress = tesile force / normal cross section area

Q: 2.7 The following readings were recorded during a tensile test of a mild steel specimen 24 mm wide…

A: Given data, Width = 24 mm Depth = 10 mm Area = 240 mm2 Length l = 200 mm Graph for the first…

Q: Determine the following: a. Young's modulus within the linear portion b. Tangent modulus at a stress…

A: a).Young's Modulus : At the proportional limit, stress is directly proportional to strain stress α…

Q: Mechanical properties of materials H.W.: The following data where obtained during the tensile test…

A: Mechanical properties are those properties of a material which can be observed under the action of a…

Q: Copy the sketch of the tensile stress-strain test (Figure A1) results for a waisted metallic…

A: Objective: To indicate the given points on the stress-strain diagram and calculate the Young's…

Q: A typical aluminum-alloy scuba diving tank is shown. The outside diameter of the tank is 20 cm and…

A:

Q: Solid shaft made of cast iron shown in the figure, T = 400 lb. It is subject to flick torque.…

A: Determine the smallest radius

Q: Problem 1.4. A tensile test was conducted on a mild steel bar. The following data was obtained from…

A:

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A:

Q: Two identical plates of 20 mm wide and 3 mm thick is connected by a square pin with side dimension…

A:

Q: (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar width b.

A:

Q: A Charpy V Notch (CVN) test was performed on a steel specimen and produced the readings shown in…

A: We have been given the following values: Sr. No Temperature(C) Toughness, Joule (N.m) 1.…

Q: The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made…

A:

Q: In a simple tensile test using a cylindrical test specimen (Dia.=10mm), the applied force was 120 kN…

A: Given data in question  Diameter of sample Force applied  Extension  Standard accepted modulus of…

Test for Determination of Shear Strength

The term shear strength is often associated with the soil. Shear strength is defined as the resistance to the deformation of soil particles due to the continuous action of shear stress. In short, shear strength is the maximum shear stress that a soil can sustain.