This is an open cylindrical vessel* It is filled 2/3. diameter = 0.60 m height = 0.90 m 90 rpm a. What is the water depth at the center of the vessel? b. What is the total force exerted on the wall? c. What is the total force at the bottom?

This is an open cylindrical vessel* It is filled 2/3. diameter = 0.60 m height = 0.90 m 90 rpm a. What is the water depth at the center of the vessel? b. What is the total force exerted on the wall? c. What is the total force at the bottom?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Consider the retaming wall shown in the Figure below Calculate the Rankine pasSIve force per unit…

A: Lateral Rankine passive earth pressure is applied at each elevation. Pressure due to Gwt table is…

Q: A 5-m diameter open cylindrical tank 10 m high contains sea water. It is made of steel 18 mm. thick.…

A: Given Data Diameter(d) = 5 m Height(h) = 10 m Thickness(t) = 18 mm Density of sea water = 1023.6…

Q: 7. A 6-in.-long bronze tube, with closed ends, is 3 in. in diameter with a wall thickness of 0.10…

Q: 9-57. The gravity wall is made of con location (x, y) of the center of mass G

Q: Q2. A tainter gate of 90° sector is subjected to water pressure as shown in figure below. Determine…

Q: Q.23 A tall open-top stand pipe has an inside diameter of 1600 mm and a wall thickness of 8 mm. The…

A: Given data- A tall open-top stand pipe- Inside diameter d=1600 mm, Thickness t= 8 mm, Mass density…

Q: 2. An open cylindrical tank 0.3m in diam and 0.8m high is filled w/ water. At what angular speed in…

A: GIven: Dia of cylindrical tank d= 0.3 m height of cylindrical tank H= 0.8 m Spilled volume V= 40…

Q: -2 ft 10 kip 4 in. -1.5 ft--- 4 in. B B 6 in. 4 kip - 0.5 ft 13 in. 2 ft- - Change the magnitude of…

A: Given:- Cross section of the beam is To find:- Maximum in plane shear stress at point A Principal…

Q: -3. What is the maximum stress which could be produced in the pipe of Prob. 6-2 as a result of…

Q: The copper pipe [G = 6,000 ksi] has an outside diameter of 3.750 in. anda wall thickness of 0.250…

Q: An orifice on a vertical wall has a head of 1.13 m of oil (sg=0.89). It discharges 6192 N of oil in…

Q: W-S. 45

Q: a. Determine the horizontal component, vertical component, and the resultant of the hydrostatic…

Q: Refer to Figure 12.13a. Given H = 4 m, α = 0, β = 85º, γ = 17 kN/m3, c' = 0, Φ' = 36º, ẟ'/Φ' = 0.5,…

A: The coefficient of active earth pressure will be: Ka=Sin2β+ϕ'Sin2β…

Q: Sand IDft 8 = 110 pef Sand 8sat= 120 pcf

Q: Question attached

A: Solution: In soil 1. at depth of z below point A, vertical stress is given byσv=r1z+qpore…

Q: 7. Gate AB as shown if figure is 2m high and 3 m wide. It supports water on the left side at the…

Q: 3. For the gate shown, α = 45°, y₁ = 1 m, and y₂ = 4 m. Will the gate fall or stay in position under…

A: Given :

Q: This

Q: 3.0 A GATE 3M HIGH IS 2.5 M WIDE IS HINGED AT POINT B AND REST AGAINST A SMOOTH WALL AT A. POINT A…

A: Answer Let us first draw the free body diagram of forces acting on the gate (a) Calculation of…

Q: Compute the stress at each segment of the pipe

A: Given Load 2500, 8000 and 8000 lbAngle 30 eachDiameter 1.5 inchesTo find out Stress in each portion

Q: 300 N 400 N A B 1 m 2 m 2 m

A: To find the forces at b is depends on the equilibrium equations,…

Q: The wall separates water and glycerin (p=120 kg/m^3). Consider a unit width of the rectangular panel…

A: Given- ρ=120Kg/m3d=6ft The diagram is given below-

Q: The 800-kg horizontal wall section is supported by the three vertical cables A, B, and C. What are…

Q: A rectangular gate 1.2 m by 3 m is inclined 60° with the horizontal. The top of the gate is…

Q: A gate 1.80 m wide and 2.70 m high has a hinge (axis of rotation) at A. The gate separates water on…

Q: 19) The Rankine active force per foot length of the wall (lb/ft) is most nearly: a. 10500 b. 3300 C.…

Q: AB, a rectangular (0.6 mx0.9 m) sluice gate, blocks a liquid with a gravity of 0.79. The weight of…

A: The figure is given:

Q: SITUATION D. From the figure shown, consider 1 unit width of gate. ws WS. 6 feet 6 feet 8. Compute…

Q: Determine the active force per unit length of the wall y = 16 kN/m 6' = 30° c' 0 3 m Groundwater…

A: To find active force per unit length of wall

Q: . A rectangular gate 1.20 m wide rests against a smooth wall at A. It is hinged at B located at 5.2…

Q: 45° SG = 0.86 | 50 cm A %3D Hinge 10 cm SG = 1.23 80 cm В

Q: F2-10. Determine the magnitude of the resultant force of the water acting on the triangular end…

A: Please refer the attached image for complete solution. THANK YOU.

Q: hydrostatic

Q: The internal shear force Vat a certain section of a steel beam is 75 kips. If the beam has a cross…

Q: A closed cylindrical tank, 1.5m in diameter and 3m high contains 2m of water & air space w/ pressure…

Q: 2. Figure 2 shows a 0.8 m wide of rectangular sluice gate is hinged at point A on the wall of a…

Q: A closed cylindrical tank, 1.5m in diameter and 3m high contain 2m of water & air space with a…

Q: total force on the sill neglecting the weight of the gate.

Q: An open cylindrical tank 0.3m in diameter and 0.8m high is filled w/ water. At what angular speed in…

A: Answer We know that tank is filled with water. Due to rotation at an angular speed 'w' 40 L pf…

Q: Situation: A 50 mm diameter bracket is securely fastened to the wall as shown. It carries the given…

A: Given data, Diameter of bracket = 50 mm Vertical load = 3600 N Horizontal load = 4000 N.

Q: ne pipe has a mass of 10 kg/m and is fixed to the wall at A. hree forces, F₁ = 310 N, F₂= 430 N, and…

Q: What is the maximum stress which could be produced in the pipe of Prob. 6-2 as a result of suddenly…

Question

This is an open cylindrical vessel*
It is filled 2/3.

diameter = 0.60 m
height = 0.90 m
90 rpm

a. What is the water depth at the center of the vessel?
b. What is the total force exerted on the wall?
c. What is the total force at the bottom?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Provide a detailed solution for this question please.
Determine the active force per unit length of the wall y = 16 kN/m3 ' = 30 c' = 0 3 m Groundwater table Yat = 18 kN/m3 = 35° d = 0 3 'm
A water tank, 22 ft in diameter, is made from steel plates that are ½ inch thick. Find the maximum height to whichthe tank may be designed if the stress of the wall is limited to 1 ksi. Assume that the pressuredistribution varies linearly.
Problem 2 Water flows through a horizontal 45 degree bend with a 22-in dimeter at a rate of 20 ft³/s under a pressure of 15 lb/in². a. In the x-direction P₁ b. In the y-direction y κα F *P2, Fx F Neglecting the head loss in the bend, calculate the resisting force required to anchor this pipe bed: X
3. A square frame 3m by 3m in dimension is submerged in water vertically with its top 4m from the surface. If oil (s = 0.80) occupies the top meter. a. Determine the horizontal pressure acting on the frame. b. Determine the pressure at the top of the gate. c. Determine the pressure at the bottom of the gate. 3m oil water |--3m- s=0.80
5. A 30 cm radius Cast iron main leads from a reservoir whose water surface is at EL. 1590m. In the heart of the city the main, below ground level, is at EL. 1410m. (a) What is the net pressure (b) Assuming static conditions, what is the stress in the pipe wall if the wall thickness is 12.00 mm and the external soil pressure is 250 kPa?6. A continuous wood stave pipe is 2.5 m in diameter and is in service under a head of 30.0 m of water. The staves are secure by means of round 25 mm steel hoops with an allowable stress of 105 MPa. Fine the maximum snarings of the hoops to safely secure the nine.
Need help. Thanks
just give a simple solution
Do not attempt wrong. Find the total pressure and center of pressure of a gate constructed across a channel which is 5m wide at the top and 2m at the bottom and 3m deep stating that the channel is fully filled with water. Total pressure =132.39kN Center of pressure = 1.82m These answer should match your solution.
Which are the Wall movements that produce the active and passive pressure conditions. Describe about them.
Give me right solution
Answer is 1266N. Please show the steps in detail.