ne pipe has a mass of 10 kg/m and is fixed to the wall at A. hree forces, F₁ = 310 N, F₂= 430 N, and F3 = 505 N, ct on the structure as shown. (Eigure 1) gure 2m < 1 of 1 Determine the resultant shear force acting in the z direction on the c Express your answer to three significant figures and include ap (VB):= = Submit ▼ Part D Value Request Answer Units SAMED ? Determine the resultant torque acting on the cross section at B. Express your answer to three significant figures and include appre

ne pipe has a mass of 10 kg/m and is fixed to the wall at A. hree forces, F₁ = 310 N, F₂= 430 N, and F3 = 505 N, ct on the structure as shown. (Eigure 1) gure 2m < 1 of 1 Determine the resultant shear force acting in the z direction on the c Express your answer to three significant figures and include ap (VB):= = Submit ▼ Part D Value Request Answer Units SAMED ? Determine the resultant torque acting on the cross section at B. Express your answer to three significant figures and include appre

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 7. [Concepts: Allowable stresses and factor of safety] Two aluminum rods AB and AC support a vertical load P. The allowable tensile stress for the aluminum is Gallow = 150 MPa. a) If P = 20 kN, determine the required diameters of the rods AB and AC. b) If the diameters of the rods AB and AC are 10 mm and 8 mm, respectively, determine the largest vertical force P that can be supported. U B
Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
(32 H.W Find longitudinal and hoor tensile stresses in the Wall of vessel Shown in figure, if the internal pressure. is 0.9 MPa and thickness of Wall is 6.4mm ? Ans: 6 = 42.19 MP₂ °H = 62.8 Mra 4 Also find I ?=0.67 Alir G 0.6m fot TE L = 1.8m O 7 0.6m
Three plates are welded together to form the section shown. Dimensions of the cross section are b= 4.7 in., d = 14.1 in., a = 2.8 in., and t= 0.5 in. For a vertical shear force of V = 42 kips, determine the shear flow through the welded surface at B. B a b Answer: kip/in.
Set P₁ = 38 kN, P₂ = 28 kN. (Figure 1) Figure B G -1.5 m 1.5 m 1.5 m 1.5 m P₁ P₂ 1 of 1 2 m Part A Determine the force in member AB of the truss. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FAB = Submit μA Value Request Answer Units ?
Please answer it clearly with FBD, I will vote it up for your effort thank you.
KINDLY DRAW THE FDB AND SHOW IN THE DRAWING THE DEFLECTION. PLEASE DRAW THE FBD OF DEFLECTION POINTS
Sispose that P = 30 kip, P=20 kip, and = 10 kip Figure ++. 400 San 184-399 30 Part A Determine the force in member GF of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension For Submit Part B Avec Fre Request Anst O? Determine the force in member PC of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension VAZO IT vec kip ? kip
Consider a cantilevered beam which is made of two identical. rectangular sections, a force P is applied at free end. 11) if A and B are not clued together, determine the bending stress distribution at a-a cross section, draw o Chint: each section carries P/ and label the Tout at the outest fibers. * 0.5m a 12) if we weld the two A & B together along the member length. determine the bending stress distribution, draw and laber. m ✓ P=1kw A 181- дет B зст
Load P is applied to joint D and the temperature increases by 50 °F. There are two steel (E = 29*10^6 psi; a = 6.5*10^-6/°F) AD and DC and a bronze (E = 16*10^6 psi; a = 9*10^-6/°F) BD with a length of 50 inches. Each bar is a 0.75 inch diameter. Find the deformation of every rod, the displacement at D, and the stress in each rod.