6.12. A 100 mm by 50 mm 180° pipe bend lies in a horizontal plane. Find the horizontal force of the water on the bend when the pressures in the 100 mm and 50 mm pipes are 105 kPa and 35 kPa, respectively.

Q: 2. Determine the x and y coordinates of the centroid of the section shown. 450 mm 720 mm K 150 mm…

A: Given data in question  Axis system Dimensions  Quarter circle 300 mm radius Triangle with base and…

Q: Draw the figure of level and show its parts on it.

A:

Q: 120N 80N 300

A:

Q: Locate the X-X centroidal axis for the cross section shown. £ sym. W840 x 329 W530 × 72 X X

A:

Q: 2) This table has three columns. First, match each set of Boundary Conditions (the left column) to…

A: Answer  Consider first Beam from middle column We get boundary condition for above beam θ0 = 0 and…

Q: TOP SE THAT Show Transcribed Text FRONT SIDE se isometric paper to construct engineering isometric…

A: Isometric view of given will draw in next step

Q: Given the multiview projection of the solid, draw its isometric view.

A: Solution- The given diagram is shown below. To Determine,  The isometric view

Q: 6. Draw a true distance between a point Q and a plane B. Vs he 7. Draw a piercing point and…

A:

Q: one help please can you help me to draw an isometric view of the bridge (truss)

A:

Q: Using virtual work methed Draw B.M.D2 4m

A:

Q: DRAW THE SECTION INDICATED BY THE CUTTIN

A: Any view obtained by a projection on a plane other than the horizontal, frontal, and profile…

Q: USing Virtuall Work method Draw Bm.D and S. fD 2 2M

A: We have to draw shearing and bending moment diagram

Q: The front and side views are given. Use this to create the top view.

A: Hi! Thank you for the question As per the honor code we are allowed to answer only 1 question at a…

Q: Given the multiview projection of the solid, draw its isometric view. HRP FRP FRP PRP ㅏ

A:

Q: Determine the y-coordinate of the centroid of the cross section of the underground runnel lining…

A:

Q: Appendix 1 shows a structural drawing of the first floor of a random building. The labels "C"…

A: Structural drawing for the first floor of the building C- Columns D1–4 is a 200 UB 29.8,3C–D is a…

Q: top wiew Units are in millimeter right side 40 IS 35 ーネィー ー子ィー front viw 1-..

A: Given orthographic views- Top view Front view Right side view

Q: 350 mm 45 KN B 500 mm 9 kN C 9kN FD KN 400 mm D Wall

A:

Q: determine the degree of indeterminacy.

A: * Hinge support: - It is defined as the support which resists horizontal and vertical reaction but…

Q: structural drawing   please indicate a details in this image

A: The structural diagram is shown in the above figure. We have to indicate a details in this image.

Q: Using this image, indicate which is the hanging wall and which is the footwall.

A: When two rocks slips on each other, the upper rock is known as hanging wall. In the same way, the…

Q: Draw the figure below in AutoCAD, take a screenshot of your work and paste it to the spaced…

A: The following image shows the given figure drawn in autocad with dimensions along with name.

Q: 10. 45 8.3 SUPPORT BRACKET 100 33 10 10 25 -

A: Question being asked here is to draw the ISOMETRIC VIEW for the given projections And the given…

Q: 0 mm Infront of VP and 30 m rojection of the line.

A:

Q: e shape factor for the section as shown -3d 3d - fe 2d

A:

Q: Subtract 8.46 from 25.3.   25.3- 8.46

A: Subtract 8.46 from 25.3.

Q: convert -0.009 °F/ft to °C/100m. Please provide the full dimensional analysis

A:

Q: In the given sketch design any of the two way slab panels. 10x21 18x12 26x12

A: Condition for two way slab l/b<2   d (effective depth) = D (overall depth) - clear cover - 1/2…

Q: a) top most, lef tmost FIND: b) botton-most, right-most 3cm S.ם r= 1.25 y 125 } 05 Vb cm 1.5 3 I 1,5…

A:

Q: The square slab of Fig. P15.1 is simply supported by masonry walls along all four sides. It is to…

A: A Slab is a structure that is highly resistant to loads that are later used on a stake axis. A…

Q: TOP VIEW 130 R30 STILLST R30 20 3X 024 65 FRONT VIEW -R30 1242- LL Ø16 R22 44 RIGHT SIDE VIEW

A:

Q: draw an isometric view of HEXAGONAL PRISM  where the base is 25mm and height 50mm.

A: Isometric view: It is also known as isometric projection. It is defined as the visual representation…

Q: Draw a neat and clean diagram of the final configuration of how the bars are placed.

A: To draw the bar configuration of the given beam

Q: 70 27 52 18 27 14 34 OC

A: Handmade drawing are attached for better understanding.

Q: Draw the sectional view indicated by the cutting plane A-A SA AL

A: ASKED: To draw the sectional view produced by the plane A-A.   To draw the sectional view using…

Q: Find the angle @g

A:

Surveys of public lands

A survey is a method used to determine the relative positions of various objects on the land by measuring the horizontal distances between them. Briefly, a survey is a process of accumulation of data of various details related to land. The main objective of surveying land is to prepare maps to a suitable scale. Various types of maps such as topographical maps, cadastral maps, engineering maps, military maps, contour maps, geological maps, archaeological maps, and so on can be prepared by surveying.