thin cylinder 500 mm in diameter is made by providing a longitudinal lap joint with 8 mm shop fillet weld on two side as shown in figure. What will be the design pressure (in /mm2) of fluid that can be allowed in the cylinder based on the strength of weld? Grade of steel used for load is Fe410. Weld

thin cylinder 500 mm in diameter is made by providing a longitudinal lap joint with 8 mm shop fillet weld on two side as shown in figure. What will be the design pressure (in /mm2) of fluid that can be allowed in the cylinder based on the strength of weld? Grade of steel used for load is Fe410. Weld

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A flat bar used as a tension member is connected to a gusset plate. Size of weld is 6 mm, with an ultimate tensile strength of 185 MPa. E 70 electrodes Thickness of plate = 6.25 mm. Use ASD. Thickness of gusset plate = 9.5 mm. Fy = 248 MPa Fw = 0.60(485) Fu = 400 MPa Questions: The connected parts are of A-36 steel and assumed that the tensile strength of the member is adequate: a) Determine the strength of the connection per mm considering the design shear strength of the 6 mm fillet weld. b) Determine the base metal shear strength per mm. c) Determine the available strength of the connection.
Situation 8: For the connection shown in the figure. Pu = 80 KN, x1 = 200, x2 = 100, y1 = 50, y2 = y3 = y4 = 100 y1 y2 y3 y4 O 80 MPa O 71 MPa O 74 MPa oooo O 86 MPa O 1. Which of the following nearly gives the shearing stress of the most stress bolt? Use 20 mm diameter bolt. x1 O O O x2
(1) Given A992 steel Ag = 10 in %3D KLy- 80, ry what is $ Pa=? = 60 the' column streugth design
Dont round off initial values, round off final ans only pls
The equivalent stress for welding in given bracket connections would be if t = 5mm e i.e. Effective throat thickness of weld, use Fe410 steel and shop welding. P = 50 kN e = 200 mm h = 250 mm
Two plates are proposed to be jointed by welding as shown in the figure. Determine the size and length of the weld required to develop the full strength of the smaller plate which is 8 cm x 1.2 cm. Assume permissible tension in plate is 1500 kg/cm? and permissible shear in fillet weld is 1025 kg/cm. 8 cm) 12 cm
A 2014-T6 aluminum tube having a cross-sectional area of 600 mm² is used as a sleeve for an A-36 steel bolt having a cross-sectional area of 400 mm², When the temperature is T=15 °C, the nut holds the assembly in a snug position such that the axial force in the bolt is negligible. If the temperature increases to T-80 °C and an axial force of 25 KN is applied to the assembly, determine the stresses in the bolt and the sleeve. Note: Length of the assembly is 150 mm, E is 200 Gpa, a is 12*106 (for bolt), E is 73.1 Gpa, a is 23*106 (for sleeve).
Q- Metal moldings should be strong to resist . .... so that .... ... they operate in all parts as a single unit. Axial loads and Lateral loads O Non of them O wind loads O Live loada only
Please solve for the value of P.
Solve and determine the design strength of a 1 - in length of a 14- in fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength of 70ksi. Assume that the load is to applied parallel to the weld length.
ASAPPP THANKS
The axial assembly consists of a solid 1.06-in.-diameter aluminum alloy [E = 9600 ksi, v = 0.31, a = 14.6 x 10-/°F] rod (1) and a solid 1.48-in.-diameter bronze [E = 12200 ksi, v = 0.18, a = 7.2 x 10-6/°F] rod (2). Assume L1=12 in., L2=27 in. If the supports at A and C are rigid and the assembly is stress free at 1°F, determine: (a) the normal stresses o1,02 in both rods at 135°F (positive if tensile, negative if compressive). (b) the displacement ug of flange B (positive if to the right, negative to the left). (c) the change in diameter Ad of the aluminum rod. B (1) (2) L1 L2 Answers: ( a) σι - i ksi, 02 = i ksi (b) ug = i in. (c) Ad, = i in.