The wheel has a mass of 100 kg and a radius of gyration of ko = 0.2 m. A motor supplies a torque M = (400+ 900) N-m where is in radians, about the drive shaft at O. Initially the car is at rest when s= 0 and 0 = 0°. Neglect the mass of the attached cable and the mass of the car's wheels. (Figure 1) Figure 94 F Sunny M 0.3 m k 1 of 1

The wheel has a mass of 100 kg and a radius of gyration of ko = 0.2 m. A motor supplies a torque M = (400+ 900) N-m where is in radians, about the drive shaft at O. Initially the car is at rest when s= 0 and 0 = 0°. Neglect the mass of the attached cable and the mass of the car's wheels. (Figure 1) Figure 94 F Sunny M 0.3 m k 1 of 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (5) The stretched spring length of the spring at the state 2 is _______(m) (two decimal places) (6) The elastic potential energy the state 2 is ___ (N·m ) (two decimal places) (7) The instantaneous center of zero velocity (IC) is (8) The mass moment of inertial about the mass center G is IG =_________(kg·m2 ) (two decimal places)
A flywheel weighing 4480 lbs has a radius of gyration of 3 ft. If there is a driving torque of 600 lb-ft, and a resisting torque of 250 lb-ft, find the time required to increase its speed from 20 to 80 rpm. The correct answer is 22.5 seconds.
In the image on the right, there is a red gear G1 on the left with a radius of r1 = 2.81cm. Gear G1 is locked to the green gear G2 with a radius of r2 = 0.734cm. Gear G2 then shares the same axle as the blue circular saw G3, which has a radius of r3 known to make a full rotation every T = 0.836s. Using at least 6 significant digits in your calculations, compute the following: V3! 12.8cm. Gear G1 is W1 a) The angular speed wi of gear G1. Remember that angular speed is measured in radians per T3 r2 unit time. G2 b) The rim speed vi of gear G1. Since gears G1 and G2 are locked together, the rim speed of G2 is also v1. G1 G3 c) The angular speed w2 of gear G2. Since gear G2 and saw G3 share the same axle, the angular speed of G3 is also w2. d) The rim speed v3 of saw G3.
The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration ke=0.4 m. The spring's unstretched length is Lo=1.0 m. The stiffness coefficient of the spring is k-2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is 8-30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is 0=0°. The spring's length at the state 2 is L2=4 m. (4) The elastic potential energy at the potion 1 is_ HULKU 2₂ State 2 G m State 1 (N-m) (two decimal places)
Solve it Analytical way By taking sigma FX , FY and moments
A gear engine automobile is traveling along a curved track of 120m radius. Each of the four wheels has a moment of inertia of 2.3 kg m2 and an effective diameter of 600 mm. The rotating parts of the engine have a moment of inertia of1.25kg m2 the gear ratio of the engine to back wheel is 3:2.The engine axis is parallel to the gear axle and the crank shaft rotates in the same sense as the road wheels. The mass of the vehicle is 2050 kg and the center of mass is 520 mm above the road level. The width by the track is 1.6m, what will be the limiting speed of the vehicle if all the four wheels maintain contact with the road surface (b) Explain the function of a flywheel from a crank effort diagram.
ENGINEERING MECHANICAL-ENGINEERING The winding drum of mass 300kg has an effective diameter of 950 mm and radius of gyration of 650 mm. The drum is driven by a motor whose efficiency is 80% through a gear reduction of 20:1. Determine; 1). Motor torque when the load is accelerated at 4 m/s^2. 2). The maximum uniform speed of the rope, if the maximum power output of the motor is 18 KW.
4. A pair of connected pulleys receive a force F = 75 N and P = 150 N as depicted in the image. The pulley system has a radius of gyration of ko 0.5 m and mass of 50kg. The radius of pulley 1 is r₁ = 600 mm, and the radius of pulley 2 is r2 = 1000 mm. Determine the angular velocity of the pulley system after it undergoes 2 revolutions starting from rest. F P₁ P
The two 1-kg gears A and B are attached to the ends of al 3-kg slender bar. The gears roll within the fixed ring gear C, which lies in the horizontal plane. (Figure 1) Figure 150 mm 400 mm- 150 mm Part A If a 10-N m torque is applied to the center of the bar as shown, determine the number of revolutions the bar must rotate starting from rest in order for it to have an angular velocity of WAB = 22 rad/s. For the calculation, assume the gears can be approximated by thin disks. Express your answer using three significant figures. ►View Available Hint(s) the number of revolutions = Submit Provide Feedback VAE vec ? Next >
only HANDWRITTEN answer needed ( NOT TYPED)
Please send me the solution of the question
The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (8) The mass moment of inertial about the mass center G is IG =_________(kg·m2 ) (two decimal places)