The Vc – Ic characteristics curves and output DC load line of a BJT amplifier are shown in Fig. 1(a). Assume that the transistor is operating at room temperature and the collector reverse saturation current of the transistor, Iş = 1.41 × 10-10 mA. i. Find the quiescent current Ico ii. Determine the Early voltage Va Ic Active Forword Mode VBe4 16 mA VBE3= VBEQ = 0.65 V IcQ VBE2 Vbei 0 Ceq= 8 V Vce 24 V - VA Fig. 1(a)

The Vc – Ic characteristics curves and output DC load line of a BJT amplifier are shown in Fig. 1(a). Assume that the transistor is operating at room temperature and the collector reverse saturation current of the transistor, Iş = 1.41 × 10-10 mA. i. Find the quiescent current Ico ii. Determine the Early voltage Va Ic Active Forword Mode VBe4 16 mA VBE3= VBEQ = 0.65 V IcQ VBE2 Vbei 0 Ceq= 8 V Vce 24 V - VA Fig. 1(a)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

DO NOT COPY FROM OTHER WEBSITES
. HAND WRITTEN PLEASE
Please answer and explain systematically.. thank you in advance
5 Rib Vs (E The following parameter for this transistor, VCC = 5V, RL = 4k2, RE = 3kN, R1 = 60kN, and R2 = 40k2, B = 100 and VA = 160. Determine: a. ICQ and VECQ, b. AV, c. Ai. d. Ro
4. Calculate the resistance Re for this circuit to drive the transistor into saturation. The BJT operates in the saturation region when its collector current is not dependent on the base current and has reached a maximum. BJT when saturated, VCE(sat) ≤ 0.2 V. $RB Is +10v Jafalka VCE = 0.2V B=150
A BJT amplifier configuration in which the base is the common terminal to an ac signal or ground. 2 la) Common Emitter b) Common Base c) Common Collector d) Common Drain
(i) (ii) Explain what happens to a BJT transistor in active mode and what its main application at this mode is. Then, state the other two modes at which a BJT transistor can operate. A BJT transistor is biased in the forward-active region. The current gain is 95 and the collector current is 475 µA. Calculate the base current, collector current and common-base current gain.
For operation as an amplifier, the base of an NPN transistor must be a. positive with respect to the emitter b. positive with respect to the collector c. negative with respect to the emitter d. OV
Figure 1 shows the transfer curves of two different type of FET transistors. The transfer curve of transistor A is shown in Figure 1(a) that has ID(on) = 5mA and VGS(on) = 7V. Meanwhile, the transfer curve of transistor B is shown in Figure 1(b). (i) Determine the type of transistor A and B. (ii) State the correct equation for the transfer curve A and B. (iii) Sketch the basic construction of transistor A and B and label each part correctly. (iv) Briefly discuss one similarity in terms of the construction between the transistors A and B. 4'o (mA) D (mA) 8 12 11 7 10 5 4 6. 3 2 1 2 3 4 5 6. 7 8 VGS 1 -5 -4 -3 -2 -1 VGs Figure 1(a) Figure 1(b)
Consider the circuit depicted in the figure shown below. This circuit is designed using a silicon bipolar junction transistor (BJT) with a forward current gain BF = 100, and two resistances RB = 1kN and Rc = 1kN. The supply voltage is Vcc = 10 volts. The currents Ig and Ic designate the base and collector currents, respectively, whereas the voltage VCẸ denotes the voltage between collector and emitter. Vcc = 10 volts Rc =1 k2 Rg = 1 k2 VCE GND Throughout this question, you will use VBE,on = 0.7 volt and VCE,sat = 0.2 volt. Recall that VBE.on is the threshold voltage of the base-emitter junction, while VCE.sat represents the voltage that is measured between collector and emitter when the BJT is saturated. a) What is the value of the base current In? Please enter the value expressed in milliamperes (mA) in the box below. For instance, if you think that IR = 0.1 A, enter 100 in the box. If you think that Ip = 10 mA, enter 10 in the box. mas-numbas-Iti.ncl.ac.uk Submit part Unanswered b)…
In the above circuit, BJT's VT values are not identical. a) For the collector currents of transistors to be 2 mA What should the R0 value be? b) Find the values for gm1 and gm2. c) Find the differential mode gain (ADM). d) Find the common mode gain (ACM). e) Find the CMRR value.
Given two pMOS transistors with Vt = -0.4 V connected in series with the source of one at 1.3V and the drain of the other open. If Vg of both transistors are at 1 V, what voltage will be at the open drain? AA 1.3 V