fast fast please electronic II Using approximate method, the DC operating parameters of the common emitter BJTamplifier are as follows: VCEQ -9.61 V and IgQ - 1.86mA with RB1 200K 2,R82 -39K Q, Vcc-18 V, B of the Si transistor is 250 and ro - infinity.%3D%3D+VccRCSRB1Io+Vo(p-p)tVi10 uFacinputVce(p-p)10 uFRB2REC;= 100 uFWhich of the following statements is true about the emitter resistance RE?O Use 2KOhms resistor for RE.D Use 1.2KOhms resistor for RE.Use 3.3KOhms resistor for RE.O Use 1.5KOhms resistor for RE.

In DC analysis of a transistor capacitors are open circuited. From the given conditions of the…

Using approximate method, the DC operating parameters of the common emitter BJT amplifier are as follows: VCEQ 9.61 V and IEQ 1.86mA with RB1 -200K 2, R82 -39K Q, Vcc 18 V, B of the Si transistor is 250 and ro - infinity. %3D %3D %3D %3! +Vcc RCS RB1 Io + Vo(p-p) +vi 10 uF ac input Vсе(p-р) 10 uF RB2 RE C= 100 uF Which of the following statements is true about the emitter resistance RE? O Use 2KOhms resistor for RE. O Use 1.2KOhms resistor for RE. Use 3.3KOhms resistor for RE. O Use 1.5KOhms resistor for RE.

Using approximate method, the DC operating parameters of the common emitter BJT amplifier are as follows: VCEQ 9.61 V and IEQ 1.86mA with RB1 -200K 2, R82 -39K Q, Vcc 18 V, B of the Si transistor is 250 and ro - infinity. %3D %3D %3D %3! +Vcc RCS RB1 Io + Vo(p-p) +vi 10 uF ac input Vсе(p-р) 10 uF RB2 RE C= 100 uF Which of the following statements is true about the emitter resistance RE? O Use 2KOhms resistor for RE. O Use 1.2KOhms resistor for RE. Use 3.3KOhms resistor for RE. O Use 1.5KOhms resistor for RE.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. TIMING DIAGRAM Positive Level-clocked D Latch CLK D
Identify the Electrical Symbol
100) Technician A says partial TCC slippage is regulated by a pulse-width modulated solenoid. Technician B says pulse-width modulation is used to vary the duty cycle of the solenoid control signal. Who is correct? Technician A O Technician B O Both technicians A and B O Neither technician A nor B
5- Analyze the synchronous counter shown in Figure 2. Construct the state diagram to show the counting sequence of the counter. B A High J Q Clock O CK CK СК K Q K Q K Q Figure 2
Choose the type of sensor that detects deformation of a diaphragm LVDT Fluid Pressure Sensor Rota meter Liquid level Sensor
A switch that can conduct positive on-state current, and can block positive or negative off-state voltage is called ___. A. voltage-bidirectional two-quadrant switch B. synchronous rectifier C. single quadrant switch D. four-quadrant switch
16) For the CRO display of a pulse waveform, the time/cm is on 18.7 ms/cm and the volt/cm switch is on 5 V/cm. The width of one complete cycle is 16.2 cm and the height of the pulse is 3cm. The time period will be___________________ seconds. 30294.00 0.33 0.00 0.30
Note: Please don't write by handwriting.
Please provide Handwritten answer
All questions solve or skip i will dislike if not solve all Use Keybord
- All bands are engaged by: A. Hydraulic servo B. Mechanical leverage C. Vacuum modulator D. None of these