The vapour pressures of the two components A and B of a binary mixture varied as follows:xA                0     0.20     0.40     0.60     0.80       1pA/Torr     0     127      246      357      457     539pB/Torr    701   631    526       394       234       38Confirm that the mixture conforms to Raoult's law for the component in large excess and to Henry's law for the minor component. Find the Henry's law constants.

Q: The following data shows the liquid-vapor phase boundary of methane. T/K 100 108 110 112 114 120…

A:

Q: What volume of ᴴ² will be combine with the 22 L ᶜˡ² (g) to form HCl (g)? What volume of HCl (g) will…

A: H2,Cl2  and HCl 22L Of Cl2  Assumption: Same temperature and pressure for all gases.

Q: Calculate the change in entropy of a system with mono atomic ideal gas at 10 moles when pressure and…

A: GivenNumber of moles of monoatomic ideal gas, n=10Initial pressure,P1=1 atmFinal pressure,P2=5…

Q: 1) Calculate the temperature increase and final pressure of Helium if one mole is compressed…

A: Compression is the process of reducing the volume of a gas and increasing its pressure. In an…

Q: Show complete solutions and enclose all final answers in a box. Round off final answers to 4 decimal…

A:

Q: Q1/Estimate the liquid density of Aniline (C H,N) at its boiling point? Molecular mass =93 *

A: Boiling point: It is the temperature at which the vapor pressure of a liquid becomes equals to…

Q: 1. Estimate the pressure for hydrate formation at 55 °F for the gas with following composition:…

A: Given that- Temperature for hydrate formation, T = 55⁰F Composition of gas is- Methane = 92.67%  =…

Q: A sample of oxygen gas was found to have a pressure of 99.3kPa when the temperature was 18.5°C. What…

A:

Q: Toluene and Benzene form an ideal solution. Prepare plots of Txy and xy at 1 atm after calculating…

A: Given, Total pressure,  P = 1 atm×760 mm Hg1 atm    = 760 mm Hg   partial pressure of the components…

Q: 10. Chlorine gas was weaponized for use on the front in WWI by compressing it into cylinders.…

A: Pressure of the system, P = 50 barTemperature of the system, T = 150°CChlorine is taken as van der…

Q: 2)        Methane    diffuses at    steady    state    through    a    tube    containing    Helium.…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: & The number of degrees of freedom for an azeotropic mixture in a two component vapeur-liquid (d) 34…

A: Given Number of component N = 2Number of phase P = 2Number of reaction R = 0s =1

Q: A real gas mixture consists of 35% N2 and 65% C2H4 (on molar basis), has a pressure of 18 MPa and a…

A: The value of the molar-specific volume of the mixture is to be determined and a comparison of this…

Q: Blank 1 is used when the boiling point of the compound (or the solvent) is too high (BP >150 °C) in…

A:

Q: 5 Calculate the bubble point temperature and the equilibrium vapour composition for a liquid…

A:

Q: Q5: Calculate the Bubble point of ternary system (liquid composition: Pentane 9 mol %, Hexane 57 mol…

A: Given liquid composition is, Mol% of pentane = 9 mol% Mol% of hexane = 57 mol% Mol% of heptane = 34…

Q: why does Xm also decreases with Ym upon an increase in temperature. Please explain

A: The temperature mole fraction phase diagram is obtained at constant pressure. On the x-axis, the…

Q: can someone break this down algebracially and show the dimensional analysis

A:

Q: Problem III (12 p): What volume of ethane (C2H6) at STP (standard temperature and pressure, assume…

A:

Q: The following data shows the liquid-vapor phase boundary of methane. T/K 100 108 110 112 114 120…

A: From the given data- T/K 100 108 110 112 114 120 130 140 150 160 170 190 P/MPa 0.034 0.074…

Q: onsider a solution containing two similar liquids which are miscible in all proportions over a wide…

A: Azeotrope mixture is that in which vapour and fluids have similar concentrations. Given that for a…

Q: Molar composition of the liquid phase

A:

Q: 1- Calculate the dryness fraction (quality) of steam which has 1.5 kg of water in suspension with 50…

A: since you have posted multiple questions , we will provide the solution only to the first question…

Q: A sample of 2.00 mol of diatomic perfect gas molecules at 250 K is compressed reversibly and…

A:

Q: For reporting of flue gases, the Orsat analysis is preferred because it already gives a complete…

A: An Orsat gas analyser is a piece of laboratory equipment used to analyse a gas sample (typically…

Q: A mixture with a 50:50 molar ratio of n-pentane and isopentane (i-pentane) is contained in a sealed…

A: An equimolar mixture of n-pentane and iso-pentane is cooled.

Q: Example 4: The molar enthalpy of a binary liquid mixture of 1 and 2 at constant temperature and…

A: Note: We are authorized to answer three subparts at a time, since you have not mentioned which part…

Q: If we have one container with 28 L of nitrogen gas at 2.00 atm and another container with 14 L of…

A:

Q: Flash Calculation

A:

Q: Bubble point pressure (T and x; are known): 1. Calculate vapor pressures of pure components from…

A: Given that, Mole fraction of n-butane x1 = 0.2 Mole fraction of n-pentane x2 = 0.25 Mole fraction of…

Q: Calculate the residual entropy of R134a (refrigerant 134a) at 300 K and 15 bar using the SRK…

A: Given that R134aT=300 k P=15 bar Psat =7.0282 bar

Q: 4. Find the fugacity (Pa) of ice (p = 0.915 g/cm³) at -10 °C and: ) P= Pat (i.e., at the sublimation…

A: Write the expression for fugacity of ice as follows: fT,P = Psat×expVP-PsatRT   .......1   Where,…

Q: Calculate the viscosity of CO2 gas at 1 atm and 2 300 K and 800K (from critical values, Lennard-…

A:

Q: Using the figure, determine the boiling point of a liquid having a molar composition of 50% A and…

A: T,x-y diagram of a binary mixture represents the variation of composition of components in liquid…

Q: You devise a new temperature scale based on the properties of the liquid propylene glycol, which has…

A:

Q: For a binary flash distillation using the McCabe-Thiele diagram, maximum vapour composition is…

A: Analysis of a binary distillation system is done using the McCabe-Thiele method as it is the…

Q: The volume of a liquid varies with temperature according to the following relationship: (³) -(0.75 V…

A:

Q: Ten grams of ice at 0 degrees celsius is dropped into 30 g of liquid water at 80 degrees celsius.…

A: Mass of ice, mice = 10 g The temperature of ice, Tice = 0°C Mass of liquid water, mW = 30 g The…

Q: Calculate the energy of 3s orbital in He+ ion. Compare it to energy of 3p. Giver E= -1312/n2 KJ/mol…

A: Given energy is E = -1312n2 kJ/mol   .......(1)   Where, n is the shell number. In 3s orbital, the…

Q: *16.13 In a handbook the vapor pressure of solid decaborane (B1H14) is given as 2642 log10 P =…

A: Step:I   Given data:-→vapor pressure of solid  decaborane B10H14…

Basic Chemical Calculations (Process and Variables)

A basic chemical calculation involves the application of the law of chemical proportions to various reactions and material and energy balance calculations on various chemical processes. Basic chemical calculation helps students analyze various chemical processes and develop problem-solving skills. The chemical manufacturing processes are divided into unit operations involving physical changes of material and unit processes involving the chemical transformation of materials. For instance, fluid flow, heat transfer, and mass transfer are unit operations, and oxidation, reduction, and pyrolysis are unit processes.