The uniform plank is initially at rest on the fixed support at A andthe stationary drum at B. If the drum begins rotating slowlycounterclockwise, determine how far the plank will travel before itcomes to rest again. (Note: Because the drum rotates slowly, theinertia of the plank may be neglected.)40.324, 0.360.30A0.283 m A force of 400 lb is applied to the pulley shown in the figure. The pulley isprevented from rotating by a force P applied to the end of the brake lever. Ifthe coefficient of friction at the brake surface is 0.20, determine the value of Pin Ibs.10400 ib16

Answered: Image /qna-images/answer/bb80e6f2-7fb7-4c35-87b8-f7ae7cdea27f.jpg

The uniform plank is initially at rest on the fixed support at A and the stationary drum at B. If the drum begins rotating slowly counterclockwise, determine how far the plank will travel before it comes to rest again. (Note: Because the drum rotates slowly, the inertia of the plank may be neglected.) 40.32 A0.28 4,0.36 M0.30 3 m

The uniform plank is initially at rest on the fixed support at A and the stationary drum at B. If the drum begins rotating slowly counterclockwise, determine how far the plank will travel before it comes to rest again. (Note: Because the drum rotates slowly, the inertia of the plank may be neglected.) 40.32 A0.28 4,0.36 M0.30 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Force P = 40N directed to the right at 20° from the horizontal and force Q = 60N directed to the right at 45° from the horizontal. Determine the magnitude of the resultant of the forces Pand Q. A) 80 N В 65 N C 98 N 56 N
Q1: It is required that the resultant force acting on the evebolt in the Figure to be directed along the positive x axis and that F2 have a minimum magnitude. Determine this magnitude, the angle 0, and the corresponding resultant force. F, - 800 N 60 F2
2. The cantilever beam below is subjected to a couple, Mo, applied at point A and is propped at point B as shown. Use the Principle of Stationary Total Potential Energy to determine the rotation and deflection at point A. (L= 36 in, Mo = 300 lb-in, I = 0.001736 in*). Mo ΕΙ L/2 B L/2
Determine the value of the maximum deflection and rotation at both ends for the beam loading shown. Assume EI to be constant all throughout the span. Explain the process. 100 N ) = 78 N/m В A 000 -3 m 2 m 1 m
Use the slope-deflection method to determine the reactions of the frame shown in Figure (2-A). B 37.5 kN/m 4m El constant Figure (2-A) 3 m 4m
The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into portion CD of the shaft. Knowing that the entire shaft is made of steel for which G = 77 Gpa, determine the angle of twist at end A. 44mm -0.6m 60mm C 2000Nm B 30mm 0.2m 0.4m 250Nm A
В 4m 100kN 5m The structure is composed of bar AB and a semi secular arc as shown in the figure. It is fixed at the lower and a 100 kN load is applied at the free end. Using E = 200 GPa, I =1000x1066 mm4. Calculate the Horizontal displacement of the point where the load is applied. (mm) 19.50 40.01 82.53 45.31 The structure is composed of bar AB and a semi secular arc as shown in the figure. It is fixed at the lower and a 100 kN load is applied at the free end. Using E = 200 GPa, I = 1000x1066 mm4. Calculate the Vertical displacement of the point where the load is applied. (mm) 86.28 46.28 68.42 35.42
Problem 7.5 For the cantilever beam shown, it is required to determine the point where two bars theoretically can be cut off from the standpoint of the calculated moment strength, OM, of the beam. f, = 420 MPa and f.'= 21 MPa. 420 3@80 = 240 90 mm 90 mm 75 mm 10mmø stirups 4-28mm¢ W. 3.6 m 800 mm 725 mm 12. Calculate the moment the moment strength, ØM, , of the section. [in kN-m] 13. Calculate the maximum factored uniform load, w, the beam could support. [in kN/m] 14. Determine the distance from the free end where two bars theoretically can be cut off. [in m] 15. Determine the distance from the free end where two bars actually can be cut off. [in m] 16. Calculate the required development length, f dr at the support, if 90 hooked bars are used. [in mm]
AND 306 mm 240 mm 240 mm 46.6 mm PROBLEM 3.9 The tailgate of a car is supported by the hydraulic lift BC. If the lift exerts a 125-N force directed along its center line on the ball and socket at B, determine the moment of the force about A.
120 kN 120 kN B C 5 m 3 m L=15 m El = constant E= 30 GPa The beam shown has a self weight of 5 kN/m in addition to the load shown in the figure. Determine the rotation at D in radians. I = 1800 x 106 mm4
A container of weight Wis suspended from ring A, to which cables AC and AE are attached. A force P is applied to the end F of a third cable that passes over a pulley at 8 and through ring A and that is attached to a support at D. Knowing that W = 1125.00 N, determine the magnitude of P. (Round the final answer to two decimal places.) 1.20 m 0.78 m 0.86 m C 1.60 m The magnitude of P is B F OF 1 E W D 0.40 m 1.30 m 0.40 m
B 5 m A -5 m- El = constant E = 70 GPa I = 1,030 (10) mm Determine the horizontal deflection of C in mm. 25 kN/m