The torsional spring at B is undeformed when bars OB and BD are both in the vertical position and overlap. If a force F is required toposition the bars at a steady orientation 0 = 54°, determine the torsional spring stiffness kt. The slot at C is smooth, and the weight ofthe bars is negligible. In this configuration, the pin at C is positioned at the midpoint of the slotted bar.5/8A6|2kTBAnswer: KT= i 0.1559FbE

Answered: Image /qna-images/answer/f85cc415-8f7b-459e-99bd-f39946257766.jpg

The torsional spring at B is undeformed when bars OB and BD are both in the vertical position and overlap. If a force F is required to position the bars at a steady orientation = 54°, determine the torsional spring stiffness kr. The slot at C is smooth, and the weight of the bars is negligible. In this configuration, the pin at C is positioned at the midpoint of the slotted bar. 6-2 Answer: KT = i 682 kT B 0.1559 Fb D F E

The torsional spring at B is undeformed when bars OB and BD are both in the vertical position and overlap. If a force F is required to position the bars at a steady orientation = 54°, determine the torsional spring stiffness kr. The slot at C is smooth, and the weight of the bars is negligible. In this configuration, the pin at C is positioned at the midpoint of the slotted bar. 6-2 Answer: KT = i 682 kT B 0.1559 Fb D F E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the reactions at the supports. Assume the support at A is fixed and that at B is a roller. Take E = 29x103 ksi. The Moment of inertia of each segment is shown in the figure. (By Using The Force Method) A 9 ft- IAB 30 k = 600 in 18 ft B 30 k IBC= 300 in | C 12 ft-
The rigid element BCD is supported by a bar AB with a diameter of 25 mm and a connection at C with a diameter of 10 mm. Determine:a. The normal stress in bar AB. b. The shear stress of the bolt at C.
The bell-crank mechanism is in equilibrium for an applied load of P = 35 kN. Assume that a = 240 mm, b = 185 mm, and 8 = 65°. The pin at B has a diameter of d = 15 mm, and the bell crank has a thickness of t = 12 mm. Calculate the average shear stress in the pin at B. (1) P Answer: T = i Bell crank a C MPa B Support bracket- b F₁ -- B
The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the weight of the structure compared with the applied loads. Is the knowledge of the size of the structure necessary? 2L 1 4L 3L 60° Answers: Ay i Dv = i Dx= i = B 60° 60° E 2L L 30⁰ L ! L D
The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the weight of the structure compared with the applied loads. Is the knowledge of the size of the structure necessary? 1L 60° Answers: Ay = i Dy= Dx= i i B 3L 60° 60° E y 1 1L L L L 30° x 4L D
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 7 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 7 mm in diameter. Assume a = 640 mm, b = 320 mm, h = 400 mm, and 8= 55°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a B KN h
Determine the magnitude of the pin force at A. Assume W = 520 Ib, a = 2.9 ft, b = 2.4 ft, r = 7 in. a C B A W D Answer: A = i Ib
The bell-crank mechanism is in equilibrium for an applied load of P= 48 kN. Assume that a = 230 mm, b = 180 mm, and 8 = 65°. The pin at B has a diameter of d = 30 mm, and the bell crank has a thickness of t= 10 mm. Calculate the bearing stress in the bell crank at pin B. (1) P Answer: O= i Bell crank A a C MPa B Support bracket b B F₁
10. The rigid bar below is supported by axial bar (1) and by a pin connection at C. Axial bar (1) has a cross-sectional area of A₁ = 275 mm², an elastic modulus of E = 200 GPa, and a coefficient of thermal expansion of a = 11.9x 106/°C. The pin at C has a diameter of 30 mm. After load P has been applied and the temperature of the entire assembly has been increased by 31°C, the total strain in bar (1) is measured as 975 μe (elongation). Determine: (a) the magnitude of load P. (b) the shear stress in pin C. 275 mm Connection detail (1) Rigid bar 540 mm 135 mm 260 mm
The solid spindle AB has a diameter ds = 1.5 in. and is made of a steel with an allowable shearing stress of 12.5 ksi, while sleeve CD is made of a brass with an allowable shearing stress of 7 ksi. Determine the largest torque T that can be applied at A. 8 in. 4 in. D B -3 in. t = in. -d₂ T The largest torque T that can be applied at A is 82.834 kip-in.
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 116 GPa] with a cross-sectional area of A₁ = 550 mm². Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A₂ = 290 mm². A concentrated load of P = 62 kN acts on the structure at D. Assume L₁=800 mm., L2=560 mm., a-590 mm., b=430 mm., and c=1160 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. a b Answers: (a) σ₁ = (b) VD = i (1) L₁ L2 (2) A B MPa, 0₂ = mm. D MPa
The bell-crank mechanism is in equilibrium for an applied load of P = 34 kN. Assume that a = 240 mm, b = 140 mm, and 0 = 63°. The pin at B has a diameter of d = 15 mm, and the bell crank has a thickness of t = 6 mm. Calculate the bearing stress in the bell crank at pin B. F₁ Bell crank B a Support bracket Part 1 Use equilibrium to determine the magnitude of the reaction force at pin B. Answer: B = i kN