BronzeSteelO = 75 mmG = 35 GPa0 = 50 mmG = 83 GPaT Tau = 80 MPaTall = 60 MPaabB.AI The compound shaft as shown is attached to rigid supports. It is subjected to concentrated torque at thejunction. The length of the steel segment is 1m.a. Determine the ratio of the length of the steel segment to that of the bronze such that thematerials willI be stressed to their limits.b. Determine the torsional reaction, in N-m, at the right supports if the applied torque at thejunction is maximized.C. determine the angle of the twist, in ° degrees, at the junction.

Answered: Image /qna-images/answer/88df7e6a-49bf-4626-b9f6-002f78484a5e.jpg

Answered: Bronze Steel O = 75 mm G = 35 GPa O =…

Engineering

Civil Engineering

Bronze Steel O = 75 mm G = 35 GPa O = 50 mm G = 83 GPa I Tou = 80 MPa Tall = 60 MPa А B. a b

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Value of one of the properties of A36 steel plate within the limit of its elasticity
1-13. The density (m ass/volume) of aluminum is 5.26 slug/ft. Determine its density in SI units. Use an appropriate prefix.
At a temperature of 37.4 °C a 0.49-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 128.7°C, determine the change in length of the steel rod if L = 328.25 mm and M = 215 mm. Round off the final answer to four decimal places.
Condition #1:E A structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook. Condition #2: The same structural support of the basic size determined in Condition 1 is subjected to a tensile load of 15 kN that is repeated several thousand times over the life of the machine. This load is not an addition to the 20 kN. Specify a suitable steel that is suitable to this application based on the basic size determined in Condition #1. Loading of Condition #1 does not apply here. Condition #3: The same structural support from Condition 2 is heated from room temperature of 25°C. The support is placed inside a frame on both ends. There is a total clearance of 0.2 mm between the support and its frame. Initial length of the rod is 200 mm. Specify the…
Plss box your final answer
Please help I need it in 30 minutes
Find the value of p
At a temperature of 29.8 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 133.3°C, determine the change in length of the steel rod if L = 312.45 mm and M=201 mm. Round off the final answer to four decimal places. d - L M - B Aluminum A = 2000 mm² E = 75 GPa a = 23 x 10-6/°C Stainless steel A = 800 mm² E = 190 GPa α = 17.3 x 10-6/°C
A simply supported beam, circular in cross section, of span L supports a point load W at mid span. The length of elastic-plastic zone at the plastic hinge will be A 0.33 L B 0.41 L C 0.50 L D 0.58 L
Q: For the Figure shown below, find the length of bronze. Use the following data: 1. E (steel) = 210 GPa and E bronze =110 GPa. 2. A (steel) = 2.5 mm² and A (bronze) = 4 mm². 3. Pst) = 2P(br.) Bronze Lbr Steel Steel L: 0.6 m 0.6 m L W (kN) (steel) (m) Name 120 1 علي باقر عبد الزهرة جاسم
value for modulus of elasticty for steel is 29000 ksi and for aluminum it is 10000ksi. yield strength for steel is 36 ksi and yield strength for aluminum is 37 ksi
5 5a 5b 5c Alaterally supported beam was designed for flexure. The beam is safe for shear & deflection. The most economical section is W 8 x 13 however the said section is not readily available at the time of the construction. If you are the engineer in charge of the construction what alternative section will be the best replacement? Why? Use: Fy=248 MPa: E=200,000 MPa Designation Ag (mm2) Weight kg/m 1910 19 30 width 24 flange. thickness d (depth) mm 200.41 bf 100.06 W8 x 10 4.32 15 expla'n briefly your cho'ce. (transform your comparative analys's 'nto a narat've form to support your cho'ce) W8 x 13 2477 202.05 101.60 6.48 W6 x 20 3787 157.48 9.27 152.91 102.36 W6 x 16 3058 159.51 10.29 tf Web 5.21 thickness tw Elastic Properties mm 4 Ix x 106 mm 3 Sx x 103 5.84 6.60 6.60 13 16 17 13 126 162 220 167 mm rx 81.79 81.53 67.56 66.04 mm 4 lyx 106 1 1 6 2 mm 3 Sy x 106 17 22 72 36 mm ry 21.36 21.41 38.10244 24.54 Plastic properties mm 3 Zx x 103 145 187 244 192 mm 3 Zyx 103 27 35 110 56…