Answered: shown carries a 50 kip-in torque.…

shown carries a 50 kip-in torque. Calculate (a) the maximum shear stress and (b) the angle of twist per foot of length. Use 2 decimal places in every solved

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: calculate the location of the centroid, the second moments and product of area for the cross-…

A: The objective of this question is to calculate the location of the centroid, the second moments and…

Q: Determire the reactiors of the given beam using morment distribution method. w = 25 kN/m, P: = 25…

Q: What is the lateral deflection at joint E in mm?

A: A truss supported at hinged support at A and roller support at E, is loaded with vertical loading…

Q: determine the maximum torque T that can be applied.

A: Solution: Allowable shear stress: Dd = 5020 = 2.5 rd = 420 = 0.20 Taken that, K = 1.25 τmax =…

Q: Rod BD is made of steel (E = 29 × 106 psi) and is used to brace the axially compressed member ABC.…

Q: A cylindrical pin made of carbon steel is loaded with a maximum possible twisting moment Mv. Maximum…

A: G = 80 GPa Maximum shear stress = 40 MPa Determine the free end distortion in degree.

Q: Determine the equation of the elastic curve. EI is constant.

A: Consider the free body diagram of the beam shown below. Consider the moment equilibrium about point…

Q: A symmetrical beam cross section is shown below. The centroid is in the exact centre of the section.…

Q: Questions a/b c₁₂=c 200 10 E 5 0.291 m 20 40 289 10 0.312 200 0.323 0.328 10 1. 6.3 kNm torque is…

A: For given data:Torque = 6.3 kN-mLength of the shaft = 3mCross-sectional area, a= 5090 mm2Modulus of…

Q: Member ABCD in figure below lies in the plane of the paper. If length L is large compared with the…

A: Consider beam section ABC and draw free body diagram

Q: The principal stresses are incorrect but the maximum shear stress is correct. What are the two…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: Problem propeller shaft for a small yacht is made of a soli steel bar 104 mm in diameter. The…

A: Length of bar, Angle of twist, diameter of the bar is given and it has been asked to determine…

Q: The shaft has a radius of 15 mm and is made of L2 tool steel. Determine the strains in the x and y…

Q: The steel shaft is formed by attaching a hollow shaft o a solid shaft. Determine the maximum torque…

Q: The bracket ABCDE is hinged at A and has a roller support resting on the angled surface, with a =…

A: The following figure shows the Free body diagram of the bracket. The reaction at hinge A is VA and…

Q: The right angle bar is supported by a pin at B and a roller at C as shown in figure. The 30 mm…

A: The right angle bar is supported by a pin at B and a roller at C as shown in figureThe 30 mm…

Concept explainers

Moments

There are various practical applications of the concept of moments, like a rotation of the crank due to linear motion of the piston, the moment of inertia and its use in designing beams and columns, bending moment concept, torque, twisting moment, etc.

Question

3 mm-
4. The cross section of the steel tube (G = 11 x 106) as
shown carries a 50 kip-in torque. Calculate (a) the
maximum shear stress and (b) the angle of twist per
foot of length. Use 2 decimal places in every solved
value.
mm
2mm
mm
3 mm
mm-
8
2 of 2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bell-crank mechanism is in equilibrium for an applied load of P= 48 kN. Assume that a = 230 mm, b = 180 mm, and 8 = 65°. The pin at B has a diameter of d = 30 mm, and the bell crank has a thickness of t= 10 mm. Calculate the bearing stress in the bell crank at pin B. (1) P Answer: O= i Bell crank A a C MPa B Support bracket b B F₁
Determine the maximum shear stress and angle of twist (in degrees) of one tip with respect to other. The material of the component has a modulus of rigidity of 24 GPa. positive applied moments are CW when seen from E to A. Moment at A= 400 N.m Moment at B = -600 N.m Moment at C= 300 N.m Moment at D = 500 N.m Moment at E= -600 N.m L is 0.25m and Radius of the rod is 30mm
The solid spindle AB has a diameter ds = 1.5 in. and is made of a steel with an allowable shearing stress of 12.5 ksi, while sleeve CD is made of a brass with an allowable shearing stress of 7 ksi. Determine the largest torque T that can be applied at A. 8 in. 4 in. D B -3 in. t = in. -d₂ T The largest torque T that can be applied at A is 82.834 kip-in.
A hollow steel crank has an outside diameter of 57 mm and an inside diameter of 52 mm. The load magnitudes are Py= 400 N and P, = 210 N, and the length dimensions are a = 125 mm, b = 344 mm, and c = 225 mm. y Py K Pz b Determine the magnitudes of the equivalent forces and the equivalent moments that act at the section that contains point K. (a) Axial force in x direction Px (N) (b) Shear force in y direction V, (N) (c) Shear force in z direction V, (N) (d) Torque around x axis Tx (N-m) (e) Bending moment around y axis M, (N-m) (f) Bending moment around z axis M, (N-m)
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 11800 psi, and the vertical deflection of joint D is not to exceed 0.600 in. when a load of P = 2900 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 92 in., b = 40 in., and c = 34 in.
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 9600 psi, and the vertical deflection of joint D is not to exceed 0.650 in. when a load of P = 2800 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 62 in., b = 22 in., and c = 24 in.