The tension member shown below is a PL 12 X 8 of A36 steel. The member is connected to a gusset plate with 1 1/8 in diameter bolts. It is subjected to the dead and live loads shown below. Does this member have enough strength? Assume that A₂ = An. If it does not have enough strength, how would you resolve this issue? »L 16x8 Dead

The tension member shown below is a PL 12 X 8 of A36 steel. The member is connected to a gusset plate with 1 1/8 in diameter bolts. It is subjected to the dead and live loads shown below. Does this member have enough strength? Assume that A₂ = An. If it does not have enough strength, how would you resolve this issue? »L 16x8 Dead

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.13.2P

See similar textbooks

Similar questions

Can u solve me step by step please . thank u
Need urgent and correct solution
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
I just need help with part b
The tension member shown in Figure below is a PL 1⁄2 × 8 of A36 steel. The member is connected to a gusset plate with-11⁄8 inch-diameter bolts. It is subjected to the dead and live loads shown. Does this member have enough strength? Assume that Ae = 0.85 An
A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of nominal diameter 1/2 in in a zig-zag arrangement as shown. Determine the tensile strength capacity Pu of the connection. Review the three limit-states: (a) yielding in the gross area, (b) rup- ture in the overall net tensile area, and (c) block shear strength.
Two plates each with thickness t = 16 mm are bolted together with 6 – 22 mm diameter bolts forming a lap connection. Bolt spacing are as follows: S1 = 40 mm, S2 = 80 mm, S3 = 100 mm. Bolt hole diameter = 25 mm. Using A36 steel having Fy = 248 MPa and Fu = 400 MPa. P P S - P S2 S2 DETERMINE: 1. Determine the allowable load Pa based on bearing at bolt holes. (ASD) 2. Determine the ultimate load Pu based on block shear.
Please do right answer and calculation.
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
A C8 x 11.5 is connected to a gusset plate with 7/8 inch diameter bolts as shown in Figure P3.2-3. The steel is A572 Grade 50. If the member is subjected to a dead load and live load only, what is the total service load capacity if the live to dead load ratio is 3? Assume that Ae=0.85An. Use LRFD and ASD.
A C8 × 11.5 is connected to a gusset plale with 22 mm diameter bolts as shown. The steel is A572 Grade 50. If the member is subjected to dead load and live load only, what is the total scrvice load capacity if the live-to-dead load ratio is 3? Assume that Ae = 0.85Ap. a. Use LRFD. b. Use ASD. Properties of A572 Grade 50: Fy = 345 MPa C8 × 11.5 Fu = 448 MPa Properties of C8 x 11.5: Ag = 2,181 mm? br = 57.4 mm d= 203.2 mm Lw = 5.6 mm lf = 9.9 mm
W 10x45 is connected to two plates with two lines of ¾” bolts as shown below. Determine the tensile strength of the system if Fy = 50 ksi and Fu = 65 ksi.