A C8 × 11.5 is connected to a gusset plale with 22 mm diameter bolts as shown. The steel is A572 Grade 50. If themember is subjected to dead load and live load only, what is the total scrvice load capacity if the live-to-dead loadratio is 3? Assume that Ae = 0.85Ap.a. Use LRFD.b. Use ASD.Properties of A572 Grade 50:Fy = 345 MPaC8 × 11.5Fu = 448 MPaProperties of C8 x 11.5:Ag = 2,181 mm?br = 57.4 mmd= 203.2 mmLw = 5.6 mmlf = 9.9 mm

Given:- A C8×11.5 is connected to a gusset plate The diameter of the bolts = 22 mm The steel grade…

A C8 × 11.5 is connected to a gusset plate with 22 mm diameter bolts as shown. The steel is A572 Grade 50. If the member is subjected to dead load and live load only, what is the total service load capacity if the live-to-dead load ratio is 3? Assume that Ae = 0.85An. a. Use LRFD. b. Use ASD. Properties of A572 Grade 50: Fy = 345 MPa Fu = 448 MPa C8 × 11.5 Properties of C8 x 11.5: Ag = 2,181 mm? br = 57.4 mm d = 203.2 mm Lw = 5.6 mm l = 9.9 mm

A C8 × 11.5 is connected to a gusset plate with 22 mm diameter bolts as shown. The steel is A572 Grade 50. If the member is subjected to dead load and live load only, what is the total service load capacity if the live-to-dead load ratio is 3? Assume that Ae = 0.85An. a. Use LRFD. b. Use ASD. Properties of A572 Grade 50: Fy = 345 MPa Fu = 448 MPa C8 × 11.5 Properties of C8 x 11.5: Ag = 2,181 mm? br = 57.4 mm d = 203.2 mm Lw = 5.6 mm l = 9.9 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

.
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem The butt connection shows 8-22 mm dia. A325 bolts spaced as follows: S1 = 40 mm S3 = 50 mm t1 = 16 mm S2 = 80 mm S4 = 100 mm t2 = 12 mm Steel strength and stresses are: Fy = 248 MPa Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Bolt Hole diameter = 25 mm Questions: Calculate the allowable tensile load T, under the following conditions. a) Based on the gross area of the plate b) Based on the net area of the plate c) Based on block shear strength
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
PLEASE ANSWER ASAP
PLS ANSWER ASAP THANKS!
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis
I need the answer as soon as possible
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions