The supporting bars (1), (2) and (3) shown are made of A992 steel [E = 29,000 ksi] and have equal diameter. If the allowable normal stress of the steel ?allow= 24 ksi: a) Determine the member forces F1, F2 and F3 using considerations of equilibrium and compatibility. b) Identify which member controls the selection of the area. c) Determine the required diameter of the bars to the nearest 1/8 in.

The supporting bars (1), (2) and (3) shown are made of A992 steel [E = 29,000 ksi] and have equal diameter. If the allowable normal stress of the steel ?allow= 24 ksi: a) Determine the member forces F1, F2 and F3 using considerations of equilibrium and compatibility. b) Identify which member controls the selection of the area. c) Determine the required diameter of the bars to the nearest 1/8 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bars of the truss each have a cross-sectional area of 1.92 in². Determine the average normal stress in ksi in member BD due to the loading P = 10 kips. NOTE: use absolute value for Normal stress. The final answer should have 2 decimal places where: L1 =3.8 ft. L2 = 4.3 ft. B L1 D L2 E 0.75 P L2
The members of the truss shown below have a cross-sectional area of 10,000 mm2. Determine the stresses in members AB and AE in MPa. Indicate if the stresses are in compression or tension. -3 m- -3 m- C E 40 kN 80 kN A 6m- 3m-
Part 2,3,4
0.13
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A₁ = 350 mm² and a length of L₁ = 2.1 m. Rod (2) has an area of A₂ = 375 mm² and a length of L₂ = 1.5 m. Assume dimensions of a = 3.2 m, b = 1.1 m, and c = 1.4 m. After a load of P = 130 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) a L2 Rigid bar L₁ Answer: (a) σ₁ = i 02= i (b) VD= i (1) B MPa MPa mm -X,U b C ↓ С D P
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A1 = 410 mm2 and a length of L1 = 3.2 m. Rod (2) has an area of A2 = 355 mm2 and a length of L2 = 1.3 m. Assume dimensions of a = 3.4 m, b = 1.2 m, and c = 1.5 m. After a load of P = 50 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) L2 a B C D x,u Rigid bar |(1) Answer: (a) o1 = i MPa 02 = i MPa (b) VD = i mm
Point B & C. Please complete solution and no rounding off.
9. Find the stresses in members BC and BE for the truss shown. The cross-sectional area of each member is 3780 mm². Indicate whether the stresses are tensile (T) or compressive (C). BC = 4.44 MPa (C), BE = 3.45 MPa (T) B C 50° 50° 50⁰° E 20 KN 50% D
i need the answer quickly
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C